1-5/16 Diameter Closed Flange For Round Rods

1-5/16 diameter closed flange gives a solid seat for round closet rods with a 1-5/16 inch outside dimension, so hanging loads bear directly on a defined pocket instead of relying only on fasteners. This Pro Value Series component is part of a closet rods and flanges system, so it fits naturally into standard closet layouts where a continuous round tube terminates at a side wall or panel. The closed style supports the rod end, which helps maintain alignment on longer runs in daily use. Flanges are made of a zinc alloy, combining metal strength with a clean machined form that suits residential and light commercial closet work. The oil-rubbed bronze finish provides a dark, uniform appearance, letting this flange match common oil-rubbed bronze closet tubing and adjacent decorative hardware across the project.

Closet Flange Details That Support Daily Use

• Flanges are made of a zinc alloy, giving a rigid metal base that carries closet rod load into the mounting panel for dependable hanging support over time.
• The design holds a 1-5/16 inch diameter outside dimension tube, so standard round closet rods in this size sit securely without excess play at the connection.
• The closed flange pocket captures the rod end, keeping the tube from shifting past the support point, which helps rods stay level along the full closet span.
• An oil-rubbed bronze finish delivers a dark tone that coordinates with matching rods and hardware, so visible terminations look consistent across the installation.
• As part of the closet rods and flanges class, this part fits typical shelf, closet, and garage organization layouts where a fixed-end rod support is required.

Pin Mount Closet Flange Installation Details

The flange has two pins, 32mm on center for 5mm bore holes and a center screw hole, so it indexes directly into system line-bored panels and then locks with a screw for pull-out resistance. This pin mount style lets the pins carry shear forces into the side panel, while the screw clamps the flange tight, which is useful on taller or heavily loaded closet sections. The 32mm spacing aligns with standard cabinet-style drilling, allowing the flange to sit square without layout measuring when used in that environment. Because the flange holds a 1-5/16 inch diameter outside dimension tube, installers can drill, seat the pins, drive the screw, and drop in a matching tube for a straightforward workflow.

Closet Rod Flange Performance In Real Projects

Where This Oil Rubbed Bronze Flange Fits Best

This closed flange for round closet rods fits into shelf, closet, and garage organization projects where a 1-5/16 inch diameter outside dimension tube is specified, so it suits typical hanging sections beneath shelves or in open wall-mounted runs. In a standard reach-in or walk-in closet, the closed pocket at the rod end defines a clear stop, which helps maintain a consistent reveal from panel to panel. The oil-rubbed bronze finish lets the flange sit visibly at the panel edge without drawing attention away from doors or face frames, since it ties into other oil-rubbed bronze hardware. In garage or utility storage using the same tube size, the zinc alloy construction provides a metal bearing surface that meets the repetitive loading from heavier garments or gear on the rod.

Why Pin Mount And Zinc Alloy Support Accuracy

The two pins, 32mm on center for 5mm bore holes, act like dowels that register the flange in a fixed position, so alignment from left to right can track the drilling pattern for accurate rod height across multiple compartments. That pin layout pairs well with 32mm system casework, letting the installer position matching flanges in mirrored panels without separate marking steps. The center screw hole then draws the zinc alloy flange face tight to the panel, which helps prevent rotation as the rod is loaded and unloaded day after day. Because flanges are made of a zinc alloy, the pocket and rim stay dimensionally stable under load, so the 1-5/16 inch diameter outside dimension tube continues to sit correctly at the bearing surface instead of wearing an oversized seat. Across a closet or garage run, those details help reduce rod sag, noise, and misalignment that can otherwise develop at rod supports.

Common Questions About This Closet Rod Flange

Select This Flange For 1-5/16 Inch Rod Runs

This Pro Value Series 1-5/16 diameter closed flange, with zinc alloy construction, pin mount design, and oil-rubbed bronze finish, matches standard 1-5/16 inch round closet tubing in system-drilled panels. When a project calls for a defined rod end support that keys into 5mm bore holes on a 32mm pattern, this flange offers a direct fit so installers can keep closet, shelf, and garage hanging sections consistent from bay to bay.