PRO Value 1-5/16" Open Round Flange with Pin, Polished Chrome, 54131 46 094

1-5/16 Inch Diameter Open Flange For Closet Rods

1-5/16 inch diameter open flange identifies this Pro Value Series fitting as sized to hold a 1-5/16 inch diameter outside dimension tube, so standard round closet rods in that size sit securely in the flange during use. The open flange design lets the rod drop in from the front rather than sliding in from the end, which simplifies rod positioning in tight closet interiors or between fixed panels. This closet rod flange is part of the Closet Rods & Flanges product class, giving it a focused role in supporting hanging tubes in closet, shelf, and garage organization setups where stable rod support is required. As a component in Closet Tubing & Flanges, it serves as a structural bearing point for the tube, helping the rod carry hanging loads evenly along the run in everyday storage applications.

Practical Details Of This Closet Rod Flange

• The flange is made of a zinc alloy, which provides a solid metal base for the closet rod so the 1-5/16 inch tube seats against a rigid support during hanging use.
• The polished chrome finish on the flange creates a bright surface that visually matches polished chrome closet rods, helping installations maintain a consistent appearance in open closets and storage areas.
• The flange holds a 1-5/16 inch diameter outside dimension tube, controlling the fit so the mating round closet rod seats into the cup without excessive play along the rod support point.
• The flange has two pins, 32mm on center for 5mm bore holes, giving installers a defined pin spacing that aligns with standard 32mm system boring patterns in closet panels.
• A center screw hole in the flange provides a direct fastener point into the panel, adding clamp force over the pin mount so the flange stays anchored under rod loading.
• The product is part of the Closet Tubing & Flanges category, so it is intended to integrate with closet tubing layouts where rods and flanges form a coordinated hanging system.

Pin Mount Closet Flange Installation Details

This pin mount closet rod flange uses two pins, 32mm on center for 5mm bore holes, so it presses into pre-drilled 5mm holes spaced on a 32mm pattern, speeding layout in system-bored closet panels. With this pattern, the flange indexes off existing vertical rows, which helps keep multiple rod flanges at a consistent height across a run of panels. The center screw hole supplements the pins by letting the installer drive a fastener through the flange into the substrate, improving resistance to pull-out when the 1-5/16 inch diameter tube is loaded with hanging items. Because the flange holds a 1-5/16 inch diameter outside dimension tube, its bore size is matched to that rod diameter, which helps the rod sit level along the opening when both ends use the same flange type.

How This Pro Value Series Flange Works In Use

Closet Rod Flange For Tubing Installations

This Pro Value Series open flange is part of the Shelf, Closet & Garage Organization category, so it is intended for installations where a round closet rod spans between supports to create hanging space. The flange is designed to hold a 1-5/16 inch diameter outside dimension tube, which aligns with common round closet rod sizing, so it functions as a stable cradle for that tube in typical closet layouts. Being classed as Closet Rods & Flanges, it serves as a mating point for the metal tube at the end or intermediate support, helping distribute hanging loads into the closet side panels or end supports. The open design allows the rod to be set into the flange from the open side, which can simplify assembly when the tube length closely matches the clear opening between panels and there is little extra space for maneuvering the rod into place from the side.

Details That Support Repeatable Closet Rod Alignment

The two pins on the flange are spaced 32mm on center for 5mm bore holes, so they reference directly off system-bored 32mm hole patterns, which supports repeatable positioning when installing multiple flanges across a bank of closets. This alignment helps keep the 1-5/16 inch diameter tube level from side to side, because each flange locates off the same vertical hole indexing rather than relying on manual measurement. The center screw hole through the flange adds a fastening point that locks the flange against the panel, which helps the zinc alloy body resist rotation or shifting when the rod is loaded. The flange is made of a zinc alloy, so the entire fitting is a single solid casting that supports the polished chrome finish, allowing the visible face to match polished chrome rods while the body provides structural bearing for the tube end.

Common Questions About This Closet Rod Flange

Selecting This Flange For Your Closet Rod Runs

This open flange from the Pro Value Series is made of a zinc alloy, holds a 1-5/16 inch diameter outside dimension tube, and mounts with two 32mm-on-center pins into 5mm bore holes plus a center screw hole, so it suits system-bored closet rod installations where polished chrome hardware is desired.