Pro Value Select Series 3" (76 mm) Center to Center Satin Nickel Pull, - SZSE3-SN

Pro Value Select Series 3 Inch Pull For Cabinets

Pro Value Select Series 3 inch pull gives a 3 inch center to center grip that matches common cabinet drilling patterns, which helps when aligning new fronts or swapping out older handles on doors and drawers. The satin nickel finish on this Select Series pull presents a consistent, muted metal look that fits well with many hinge and appliance finishes in the same color family. The pull length of 3-1/4 inch provides just enough bar beyond the screw holes for a comfortable hand hold in daily use. A projection of 1-1/4 inch sets the pull out from the face of the cabinet, creating finger clearance that supports easy opening without scraping knuckles. The 1/2 inch width keeps the profile slim on narrow rails, which matters when laying out multiple pulls on smaller drawer fronts. As part of the Pro Value Series, this pull sits in a decorative hardware range aimed at practical cabinet and furniture projects.

Key Satin Nickel Pull Details For Daily Use

• The 3 inch center to center measurement defines the screw hole spacing, which simplifies layout on new cabinet work and matches one of the most common retrofit sizes in kitchen and bath projects.
• A 3-1/4 inch overall length keeps the pull compact, which helps when positioning handles near adjacent doors or walls where there is limited edge clearance.
• The 1-1/4 inch projection gives space behind the pull for fingers, which supports comfortable gripping on heavier drawers without contact against the cabinet face.
• A 1/2 inch width keeps the pull visually light, which suits slimmer drawer fronts and reduces crowding when several pulls sit close together on multi-drawer bases.
• The satin nickel finish offers a subdued metallic surface, which fits into projects using other satin nickel decorative hardware elements in the same room.
• Zinc die cast material forms the body of the pull, which provides a solid-feeling handle suitable for repeated opening and closing in typical cabinet use.
• The 8-32 x 1 inch screw size matches a standard cabinet thread and length, which supports straightforward installation into typical cabinet door and drawer materials.

Mounting And Fit Details For This Cabinet Pull

This satin nickel pull is designed around a 3 inch center to center dimension, which means drilling or existing holes at that spacing will align with the pull stems for a direct mount. The 8-32 x 1 inch screw size specified for this handle corresponds to a widely used cabinet hardware thread, so it engages properly with standard cabinet boring for pulls. A 3-1/4 inch overall length keeps the handle body only slightly longer than the mounting spread, which is useful near inside corners where a longer bar could interfere with adjacent fronts. With a projection of 1-1/4 inch off the surface, the handle stands out far enough to grip from above or below on both doors and drawers. The 1/2 inch width helps the pull sit neatly on narrow stiles, supporting consistent alignment across mixed cabinet sizes in the same run.

Using This Satin Nickel Pull In Cabinet Projects

Where This 3 Inch Center Pull Fits Best

This Pro Value Select Series pull fits installations calling for a 3 inch center to center layout, which is common on face frame and frameless cabinet lines. On cabinet doors, the 3-1/4 inch length places the hand grip close to the stile edge, keeping the motion tight and controlled. On drawers, the combination of 3 inch mounting spread and 1-1/4 inch projection supports use on both shallow and deeper boxes by giving enough clearance for a secure pull. The satin nickel finish coordinates with other satin nickel decorative hardware and moldings, which supports a unified look when pairing this handle with hinges and knobs from the same color group. Because the pull falls under the handles and pulls category, it suits projects ranging from new cabinet installations to furniture pieces that use standard cabinet drilling.

Details That Support Repeatable Cabinet Hardware Results

The defined 3 inch center to center measurement allows jigs or drilling templates to be set once and reused across multiple doors and drawers, which speeds layout and keeps hardware alignment consistent. Knowing the 3-1/4 inch length in advance helps in planning clearance from edges, so the handle ends do not overlap neighboring panels. The 1-1/4 inch projection and 1/2 inch width work together to balance grip space and visual scale, which matters when repeating the pull across a long run of cabinets where any odd proportion would stand out. Zinc die cast construction creates a uniform casting, which supports predictable contact points against the cabinet surface. The satin nickel finish gives a stable surface appearance, which helps maintain a consistent look across several pulls ordered under the same Select Series designation. The stated 8-32 x 1 inch screw size ties the pull to a known fastener format, which helps coordinate hole boring depth and thread engagement in common cabinet materials.

Common Questions About This Pro Value Cabinet Pull

Choose This Pull For 3 Inch Cabinet Layouts

The Pro Value Select Series 3 inch pull with satin nickel finish, zinc die cast construction, and 3 inch center to center layout suits cabinet and furniture projects built around this common drilling pattern. The 3-1/4 inch length, 1-1/4 inch projection, and 1/2 inch width define how it sits on doors and drawers, supporting consistent placement across a room. With the SZSE3-SN part number, this handle ties directly to the Select Series line for projects calling for matching satin nickel decorative hardware. Select this pull when a practical 3 inch center to center cabinet handle is needed in a satin nickel look.