
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
2PC 1 3/4 wire grommet black describes a 2-piece wire grommet set with a cap and liner in black, so cable pass-throughs match dark surfaces in desks, counters, or workstations. The bore hole size is 1-3/4 inches, so this grommet drops into a precisely drilled opening without extra trimming, keeping hole layout predictable on jigs and templates. The liner depth is 3/4 inch, so the grommet seats with a defined grip in typical panel thicknesses, helping the opening edge stay protected from wear when wires move. An overlapping trim edge with smooth finish covers minor chipping around the cut, which helps finished tops look clean after boring. The product name and description identify it as a wire grommet for multimedia and workspace components, so it suits projects where power, data, or audio leads need a clean route through a surface.
The web description states the bore hole size is 1-3/4 inches, so installers can cut the opening with a 1-3/4 inch bit and rely on a snug drop-in fit. The liner depth is 3/4 inch, providing enough sidewall to register positively in the panel while leaving room under typical worktops for cable bend radius. The overlapping trim edge with smooth finish is designed to sit on top of the surface, so slight variations in drilling are visually covered while still reading as a tight, intentional opening. Because the cap has a built-in permanent wire hole, the cable exit point stays defined, helping cable bundles stay grouped and reducing the chance of wires rubbing directly on the raw panel edge.
The category designation lists this product under multimedia and workspace components, so it is aligned with applications like desks, countertops, and workstations where wires must pass cleanly through horizontal or vertical panels. The black finish coordinates with dark laminates or painted surfaces, helping the opening visually recede on darker furniture. A 1-3/4 inch bore hole size means it is sized for smaller cable clusters, which suits power leads, data lines, or monitor cords rather than large conduit runs. The liner depth of 3/4 inch gives protection along the edge of the hole, so repeated cable movements during reconfigurations are guided against a smooth surface instead of raw substrate. The overlapping trim edge with smooth finish helps maintain a neat appearance in front-of-house or client-facing installations where exposed cut edges would be unacceptable.
This grommet is described as a 2-piece wire grommet cap and liner, so the liner stabilizes in the 1-3/4 inch bore while the cap sets the visible profile and wire exit point. That separation allows installers to drill a consistent hole and then rely on the liner depth of 3/4 inch to seat the body, which supports repeatable installs across a run of workstations. The overlapping trim edge with smooth finish provides a defined bearing surface that references off the panel face, so as long as the hole is properly located, the trim automatically squares and covers the perimeter. The cap has a built-in permanent wire hole, which means the opening for cables remains constant, helping maintain cable alignment and reducing visual clutter at the entry point. The combination of a defined bore size, fixed liner depth, and permanent wire hole supports predictable cable routing patterns that can be repeated across multiple furniture pieces.
The grommet uses a bore hole size of 1-3/4 inches, so installers cut that opening and then drop the liner in for a close, repeatable fit on desks or work surfaces.
The liner depth is 3/4 inch, so the body engages the panel sidewall enough to stay stable while providing a smooth, protected edge for passing cables.
The overlapping trim edge with smooth finish covers the cut perimeter, hiding minor chipping and giving the cable opening a clean, finished appearance.
The 2-piece wire grommet with cap and liner lets the liner stabilize in the bore while the cap defines the visual opening and wire exit point at the surface.
The cap has a built-in permanent wire hole, so cables exit through a fixed opening, keeping routing consistent and reducing movement at the panel edge.
The product is categorized under multimedia and workspace components, so it suits desks, countertops, and similar work areas needing organized cable pass-through.
The Hardware Concepts, Inc. 6325-014 2-piece wire grommet combines a 1-3/4 inch bore hole size, 3/4 inch liner depth, and overlapping trim edge with smooth finish to create a clean cable opening. The black cap with built-in permanent wire hole supports controlled cable routing on dark desks, counters, or workstations. For projects organized around multimedia or workspace components, this wire grommet aligns hole sizing, edge protection, and cable exit control into one part that standardizes how wires pass through finished surfaces.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each | PL6320BL Mfr# 6320-014 | 6320 2" 1-Piece Wire Grommet Liner, Black | ||||
Sold in: 1 Each | PL6320WH Mfr# 6320-010 | 6320 2" 1-Piece Wire Grommet Liner, White | ||||
Sold in: 1 Each | PL6325WH Mfr# 6325-010 | 6325 2" 2-Piece Wire Grommet Cap/Liner, White |