Salice 0mm Steel Mounting Plate For Hinges

Salice 0mm steel mounting plate gives you a flat, zero-offset base for Salice hinges, which helps keep door reveals consistent across a run of cabinets. Being part of the hinge mounting plates category, it serves as the fixed reference point for your door alignment, so case work and doors stay in sync over time. The plate is constructed of stainless steel nickel plated, corrosion resistant, which helps it stand up to typical cabinet environments where humidity and handling can cause wear. All mounting plates compatible with any Salice hinge series, so one plate style can support different Salice hinge lines on the same project. This plate is backed by a lifetime warranty, providing long-term assurance that the mounting interface remains stable throughout the life of the installation.

Key Mounting Plate Details That Help Jobs Run Smoothly

• All mounting plates compatible with any Salice hinge series, so one part number can be used wherever Salice hinges are specified on a project, simplifying ordering and jobsite planning.
• Hinge affixes to plate by sliding hinge onto plate and then tightening pre-mounted screw on plate, which creates a straightforward mounting motion and helps maintain consistent clamping force from hinge to case.
• Height adjustment of plus or minus 2 mm by slotted holes, allowing fine tuning of door positioning after mounting so reveals can be corrected without re-drilling or changing components.
• Standard 37 mm x 32 mm positioning, giving a known reference layout on the cabinet side that supports repeatable boring patterns from cabinet to cabinet.
• Constructed of stainless steel nickel plated, corrosion resistant, helping the plate resist rust and surface degradation where moisture, cleaning, or handling would otherwise affect long-term hinge performance.
• Belonging to the hinge mounting plates product class, this part ties the cabinet and Salice hinge together in a consistent way that supports reliable door operation on finished installations.

Mounting, Adjustment, And Fit For Salice Hinges

This Salice hinge mounting plate uses standard 37 mm x 32 mm positioning, giving you a predictable footprint when laying out case sides or drilling on a line boring machine. The hinge affixes to plate by sliding hinge onto plate and then tightening pre-mounted screw on plate, so the installer uses a simple slide-and-tighten motion instead of juggling separate fasteners. Height adjustment of plus or minus 2 mm by slotted holes lets you shift the door up or down relative to the case, which is especially helpful for bringing multiple doors into the same plane on tall runs or banks of cabinets.

How This Hinge Mounting Plate Works In Practice

Where This Salice 0mm Plate Fits Into Cabinet Work

The Salice 0mm steel mounting plate functions as the fixed base that any Salice hinge series locks onto, so it sits on the cabinet side or frame where the hinge load is carried. With a 0mm plate, the door-to-cabinet offset remains minimal, which keeps the hinge geometry close to the hardware design intent. Standard 37 mm x 32 mm positioning means the screw or boring layout is the same from cabinet to cabinet, helping shops use one drilling program across different carcasses. As part of the hinge mounting plates product class, it bridges the Salice hinge cup in the door to the cabinet structure, transferring opening and closing forces into the case. All mounting plates compatible with any Salice hinge series, which helps consolidate inventory where multiple Salice hinge models are used but the mounting interface on the cabinet side is the same.

Why Adjustment And Construction Details Support Repeatable Results

Height adjustment of plus or minus 2 mm by slotted holes provides post-install fine tuning of the door position, so an installer can correct small layout variations without re-boring or replacing the plate. The hinge affixes to plate by sliding hinge onto plate and then tightening pre-mounted screw on plate, so the engagement between hinge and plate remains consistent each time a door is hung or rehung. Constructed of stainless steel nickel plated, corrosion resistant, the plate keeps its surface integrity as doors are cycled and adjusted over time, which supports stable screw holding and hinge alignment. The 0mm designation gives a defined baseline height in the Salice system, allowing door and hinge planning to reference a known mounting plane. The lifetime warranty indicates that the mounting interface is intended for long service life in typical woodworking and cabinet environments, which supports long-term door function on residential or commercial projects.

Common Questions About This Salice Mounting Plate

Selecting This Plate For Salice Hinge Installations

Choosing the Salice 0mm steel mounting plate ties your project to a known 0mm reference height in the Salice system, which helps keep layouts predictable across multiple cabinets. All mounting plates compatible with any Salice hinge series, so one part number can support varied Salice hinge choices on a job. The stainless steel nickel plated, corrosion resistant build and lifetime warranty align with long-term cabinet use where hinges are adjusted and cycled repeatedly.