1/4 inch air hose assembly 25 ft delivers a defined path for air and fluid between spray equipment and spray guns so air and material reach the gun where finishing work happens. The hose assembly is specified as an air hose assembly, aligning directly with air-driven spray workflows. Manufacturer part 53-111-25 identifies this exact C.A. Technologies assembly so jobs that follow this part number can be repeated with the same hose setup. The air hose uses a smooth red synthetic rubber casing, giving a distinct color cue along runs where different hose functions share a workspace. Textile reinforcement carries load within the air hose, supporting the stated 200 psi working pressure for air during spraying. An oil resistant casing is specified for both air and fluid hose sections, so the hose construction handles exposure to lubricated air and oil-bearing coatings in typical spray environments.
The 25 ft length defines how far this hose assembly can bridge between air source, pump, and spray gun without adding joints, which matters when planning booth layouts and mobile rigs. The air hose 1/4 inch size sets the flow path dimension, giving installers a known interface when matching hose ends to air fittings rated for the same size. The air hose temperature range from -20 to +190 degrees F defines conditions where the hose maintains its specified performance, so this range can be matched to where the hose will be routed in the shop. The fluid hose temperature range of 0 to 190 degrees F sets a separate band tailored to liquid coatings, so finishers can align their coating temperatures to this defined capability.
This C.A. Technologies air hose assembly sits in spray equipment and spray guns workflows, as defined by its category listing under Spray Equipment and Spray Guns, Accessories. The air hose portion manages compressed air up to 200 psi working pressure, fitting typical spray gun air demands where stable air delivery is needed. The fluid hose portion is specified with a 750 psi working pressure, aligning the material side with higher pressure requirements seen between pumps and spray guns in finishing systems. Nylon 11, specified as the fluid hose tube material, provides a silicone-free fluid path, which is significant in finishing environments that specify silicone-free components to support coating appearance. Braided high strength synthetic yarn in the fluid hose construction supports pressure containment along the length of the hose, helping material delivery remain consistent from pump to gun. The smooth black synthetic rubber casing described as RMA B ORS defines the external layer of the fluid hose, pairing oil resistance with a uniform outer surface that moves cleanly across floors, racks, or supports during repositioning.
Oil resistant casings on both the air and fluid hoses allow the assembly to function in areas where lubricated air lines and oil-bearing coatings are part of everyday spray practice, which helps the hose maintain its described performance in those conditions. The air hose textile reinforcement supports the 200 psi working pressure specification, so compressed air can be supplied within that rating while the reinforcement manages internal force rather than relying on wall thickness alone. The fluid hose braided high strength synthetic yarn supports the 750 psi working pressure, giving a defined structure that carries pressure, which helps maintain stable coating feed during spraying routines that rely on consistent material delivery. Temperature ranges defined as -20 to +190 degrees F for the air hose and 0 to 190 degrees F for the fluid hose set the operational envelopes, so the hose assembly characteristics are tied directly to known environmental and process heat conditions in finishing operations. The smooth outer synthetic rubber casings on both hose sections reduce surface irregularities, which supports easier pulling and repositioning of hoses around equipment, fixtures, and workpieces during spraying.
The 1/4 inch designation refers to the air hose size, which defines the air flow path and helps match this assembly to spray equipment fittings designed for that hose dimension.
The C.A. Technologies air hose assembly 53-111-25 is 25 ft long, giving a fixed distance between air source, pump, and spray gun for booth layouts or mobile spray setups.
The air hose section supports a 200 psi working pressure, allowing it to serve compressed air delivery for spray guns within that specified pressure range in typical spray operations.
The fluid hose portion is rated at 750 psi working pressure, supporting higher-pressure coating delivery from pumps to spray guns where that pressure capacity is required.
The fluid hose uses a Nylon 11 silicone-free tube with braided high strength synthetic yarn reinforcement and a smooth black synthetic rubber casing, creating a defined path and structure for coating flow.
The air hose operates from -20 to +190 degrees F, while the fluid hose operates from 0 to 190 degrees F, defining environmental and process temperature limits for this assembly.
This 1/4 inch air hose assembly 25 ft from C.A. Technologies combines specified temperature ranges, oil resistant synthetic rubber casings, and defined working pressures for both air and fluid lines, so spray operations can align hose choice with clear performance ratings. Using manufacturer part 53-111-25 keeps hose selection tied to a consistent specification whenever the same spray workflow is repeated or expanded across additional spray stations.
Sold In: 1 Each