Berenson Advantage Plus Five Pull 3" (76 mm) Center to Center, Brushed Nickel, 9378-1BPN-P

Berenson Advantage Plus Five Pull For Cabinets

Berenson Advantage Plus Five pull gives a 3 inch center to center grip that lines up with standard cabinet drilling, which helps installers swap or add pulls without layout changes. The brushed nickel finish provides a consistent, modern look that works well across multiple door and drawer fronts. Zinc die cast construction creates a solid-feeling pull that holds up when used repeatedly on busy cabinets. The overall 4-1/2 inch length offers extra hand room beyond the 3 inch screw spacing, making it easier to grab with different hand sizes. A projection of 1 inch stands the pull off the surface so fingers clear the door or drawer face during use. The 3/8 inch width keeps the profile slim, which is useful when fitting multiple pulls along narrower rails or smaller drawer fronts.

Key Pull Details That Support Cabinet Work

• The 3 inch center to center dimension matches a common drilling pattern, which simplifies aligning multiple pulls in straight runs on doors and drawers.
• The brushed nickel finish gives a uniform appearance across a project, which helps maintain visual consistency in kitchens, baths, or built-ins using similar finishes.
• Zinc die cast material provides a sturdy pull body, which supports repeated opening and closing without the handle feeling fragile in daily cabinet use.
• The 4-1/2 inch overall length offers more gripping area than the screw spacing alone, which is useful on wider drawer fronts where users expect a broader handhold.
• The 1 inch projection spaces the pull off the face, which lets fingers wrap behind the handle rather than scraping the door or drawer front.
• The 3/8 inch width keeps the handle visually light, which helps it sit neatly on narrower stiles or smaller doors without overwhelming the front.

Installation Dimensions For Accurate Pull Layout

The 3 inch center to center screw spacing defines where holes are drilled, which lets installers reuse existing 3 inch layouts or create new rows that match typical cabinet boring jigs. The 4-1/2 inch overall length sets the visual footprint on the door or drawer, which matters when balancing the pull with rail widths and panel proportions. A base diameter of 3/4 inch at each mounting point gives a stable bearing surface, which helps spread load and keep the pull seated flush against the cabinet front. The 1 inch projection and 3/8 inch width together define the hand clearance profile, which helps plan around adjacent doors, tall drawer stacks, or nearby walls. An 8-32 thread size for mounting uses a widely available machine screw standard, which supports straightforward fastening into cabinet fronts tapped or drilled for that thread.

Using This Brushed Nickel Pull In Cabinet Projects

Where This 3 Inch Cabinet Pull Works Well

This 3 inch center to center cabinet pull suits doors and drawers drilled on the common 3 inch pattern, which keeps layouts consistent across banks of cabinets. The brushed nickel finish makes the pull suitable where a muted metallic look is desired, which can coordinate with brushed faucets, hinges, or other decorative hardware using similar tones. With an overall length of 4-1/2 inches, the pull fits well on typical base, wall, and vanity cabinet fronts, which helps one model carry across multiple cabinet sizes without looking undersized. A projection of 1 inch keeps the pull from sticking out excessively into walk paths while still providing usable finger clearance, which is important on tight galley runs or smaller rooms. The 3/8 inch width keeps the handle visually balanced on narrow frames, which is useful on smaller doors, spice pull-outs, or utility cabinets that share the same hardware family.

Why These Pull Dimensions Support Repeatable Results

The fixed 3 inch center to center measurement aligns with many drilling templates, which streamlines repeat cabinet production or large retrofit jobs using the same hole spacing. The 3/4 inch base diameter at each end offers a defined landing area around the screw hole, which helps cover minor drilling chips and gives a clean transition from pull to door surface. Zinc die cast construction provides a consistent casting shape, which supports uniform alignment when installing multiple pulls in long runs of uppers or lowers. The 1 inch projection ensures the gripping surface sits at a predictable distance from the face, which allows installers to anticipate clearance around face frames, door reveals, and adjacent hardware. The brushed nickel finish offers a repeatable surface appearance, which matters when multiple pulls are mounted side by side where even slight variations would stand out. The 4-1/2 inch overall length provides a reliable reference for centering the pull on different panel widths, which helps maintain even sight lines from cabinet to cabinet.

Common Questions About The Berenson 9378-1BPN-P Pull

Selecting This Pull For Your Next Cabinet Run

The Berenson Advantage Plus Five Series 9378-1BPN-P pull combines a 3 inch center to center layout with an overall 4-1/2 inch length, which suits many standard cabinet fronts. Brushed nickel finish and zinc die cast construction provide a consistent look and solid feel across a project. With 1 inch projection, 3/8 inch width, and 3/4 inch base diameter, the pull offers defined mounting and hand clearance dimensions that support efficient cabinet work. For projects calling for brushed nickel hardware on 3 inch drilling, this pull offers a straightforward, dimensionally clear option.