Berenson Advantage Plus Five Pull 3-3/4" (96 mm) Center to Center, Brushed Nickel, 9393-1BPN-P

Berenson Advantage Plus Five Pull For Cabinets

Berenson Advantage Plus Five pull gives you a 3-3/4 inch (96 mm) center to center handle that installs on standard cabinet and drawer layouts, so hole spacing lines up cleanly on face frames and fronts. The brushed nickel finish provides a neutral metallic look that coordinates with many hinge finishes and appliances in the same space. Its zinc die cast construction creates a solid-feeling pull with a consistent profile along the grip, which helps doors and drawers open with a steady hand feel. Overall length of 4-1/4 inches keeps the pull visually balanced on common cabinet widths while leaving edge clearance at each side. A projection of 1-7/16 inches sets the hand grip off the surface enough for fingers to wrap comfortably during everyday use.

Key Details That Streamline Cabinet Hardware Layout

• The 3-3/4 inch (96 mm) center to center dimension lets you line this pull up with widely used drilling patterns, which helps keep cabinet runs consistent when you repeat the layout across doors and drawers.
• The 4-1/4 inch overall length provides a defined grip section with short overhangs at each end, which supports a tidy look on both narrow and wider fronts without crowding nearby hardware.
• The 1-7/16 inch projection sets the handle out from the surface so fingers clear the cabinet face, which reduces knuckle contact against doors or drawer fronts while pulling.
• The 5/8 inch width along the pull gives a slim profile, which helps the handle sit visually light while still presenting a clear edge to grab during regular opening and closing.
• The 11/16 inch base diameter at each post creates a stable footprint against the cabinet surface, which helps distribute pulling force at the attachment points.
• The brushed nickel finish offers a muted sheen on the zinc die cast body, which works well in jobs calling for a modern but not high-gloss metal look.

Installation Dimensions For Accurate Handle Placement

This Berenson Advantage Plus Five pull uses a 3-3/4 inch center to center measurement, so drilling two holes at that spacing sets the posts exactly where the handle mounts. With a 4-1/4 inch overall length, there is approximately a quarter inch of material beyond each hole, which leaves a visible end beyond the mounting points for alignment against stile edges or drawer borders. The 1-7/16 inch projection establishes how far the grip stands off the face, which helps when planning clearances near adjacent doors, tall surrounds, or trim. A 5/8 inch width and 11/16 inch base diameter define the footprint on the front, which can be useful when laying out on narrow rails where available flat area is limited.

Using This Brushed Nickel Pull In Cabinet Projects

Where This 96 mm Cabinet Pull Fits Best

The 3-3/4 inch (96 mm) center to center layout on the 9393-1BPN-P pull suits cabinet doors and drawers that follow common metric and imperial drilling patterns, so it works across many kitchen, bath, and shop storage runs using that spacing. Its 4-1/4 inch overall length and 5/8 inch width make the pull a practical size on both base cabinets and wall units, where it stays proportional without overwhelming smaller fronts. The brushed nickel finish sits comfortably with many decorative hardware and molding choices in the same metal family from Berenson Corporation, helping maintain a unified look on multi-room projects. Because the pull is made from zinc die cast material, it offers a uniform shape from piece to piece, which supports consistent sight lines across long rows of doors.

Details That Support Repeatable Layout And Operation

The defined 3-3/4 inch (96 mm) center to center measurement on this zinc die cast cabinet pull simplifies jig use when drilling repetitive runs, since a single setup can be used across doors and drawers sharing that spacing. The 1-7/16 inch projection provides a repeatable stand-off from the door surface, which helps maintain even finger clearance when cabinets are placed near walls, appliances, or tall panels. With an 11/16 inch base diameter anchoring each side, the pull spreads operational force over a slightly larger area of the front, which is useful on frequently used drawers. The combination of 5/8 inch grip width and brushed nickel finish delivers a predictable tactile feel from handle to handle, so users experience the same grip and visual cue at every cabinet location along the run.

Common Questions About This Berenson Cabinet Pull

Select This Pull For 96 mm Cabinet Layouts

The Berenson Advantage Plus Five brushed nickel cabinet pull, part number 9393-1BPN-P, provides a 3-3/4 inch (96 mm) center to center layout in a zinc die cast body that suits many cabinet and drawer runs. Its 4-1/4 inch overall length, 1-7/16 inch projection, and 5/8 inch width give clear dimensional references when planning hole locations and clearances on new or refreshed fronts. For projects calling for a brushed nickel metal look with consistent sizing across multiple openings, this pull aligns directly with common drilling patterns and visual expectations.