R. Christensen by Berenson Fuji Pull 8-13/16" (224 mm) Center to Center, Brushed Nickel, 1188-1BPN-C

Fuji Pull 224mm Center To Center For Cabinets

Fuji pull 224mm center to center describes this R. Christensen by Berenson Fuji Series brushed nickel pull with an 8-13/16 inch center to center drilling, which aligns with common cabinet hole spacing and helps streamline layout on doors and drawers. The Fuji name and 1188-1BPN-C part number identify a specific decorative handle, which supports consistent appearance across multiple cabinets on a project. Its brushed nickel finish diffuses light on the zinc material, which helps the pull sit visually between stainless and chrome hardware on job sites. The pull length of 12-1/2 inches spreads the grip area along wider fronts, which can assist when opening larger cabinet doors. A projection of 13/16 inch and width of 1-1/4 inch define the hand clearance and front coverage, which guides positioning on both residential and commercial cabinetry.

Key Fuji Series Pull Details For Projects

• The Fuji Series designation links this pull to a coordinated decorative hardware line, which supports consistent styling when the same profile is repeated on multiple cabinets.
• Material listed as zinc defines the metal base of the pull, which affects weight, machining behavior, and how the brushed nickel finish presents on finished cabinets.
• The brushed nickel finish on zinc provides a muted metallic surface, which helps the pull visually pair with other brushed fixtures around casework and workspaces.
• The 8-13/16 inch center to center dimension sets the bore spacing, which guides drilling locations for handles on cabinet doors and drawer fronts.
• The 12-1/2 inch overall length extends past the mounting holes, which distributes the visual mass and hand contact area across wider cabinet faces.
• The 1-1/4 inch width defines the front face of the pull, which influences grip feel and how the hardware visually scales against different door and drawer widths.

Installation And Fit Details For This Pull

The 8-13/16 inch center to center measurement on this Fuji pull sets the exact distance between mounting points, which allows installers to plan drilling patterns that align across banks of cabinets. The projection of 13/16 inch from the cabinet face establishes how far the pull stands off the surface, which affects finger clearance when grasping from above or below. A width of 1-1/4 inch defines how much of the door or drawer face is covered, which can help mask minor layout variations along the mounting line. With an overall length of 12-1/2 inches, the handle spans more of the front, which can assist when aligning hardware visually with adjacent panels or appliance fronts.

Using The R. Christensen Fuji Pull In Cabinet Work

Where The 224mm Fuji Pull Is Typically Used

This Fuji Series brushed nickel pull from R. Christensen by Berenson is positioned for use on cabinet doors and drawers where an 8-13/16 inch center to center drilling is specified, which matches its 224 mm center to center dimension. The 12-1/2 inch overall length suits wider fronts, which is useful on large base cabinets, tall pantry doors, or broad drawer stacks. Its zinc construction with a brushed nickel finish provides a decorative hardware option within the Decorative Hardware & Moldings, Handles and Pulls category, which connects it to typical kitchen, bath, and casework installations. The defined projection of 13/16 inch shapes how far hands sit from the cabinet face, which matters on cabinets near adjacent walls or appliances. The 1-1/4 inch width creates a noticeable front profile, which can be used to balance proportions on taller or thicker doors.

Why These Fuji Pull Details Support Consistent Results

The specified 8-13/16 inch center to center dimension on this 1188-1BPN-C Fuji pull allows installers to repeat the same bore spacing across multiple fronts, which supports consistent alignment and reduces layout variation across a run of cabinets. Knowing the 12-1/2 inch overall length ahead of time lets designers position the pull relative to panel edges, which helps maintain uniform visual margins on wide drawers or doors. The 13/16 inch projection determines how far the pull clears the door surface, which influences how the hardware interacts with surrounding trim or adjacent cabinet faces. The 1-1/4 inch width provides a clear reference for how much hardware will show on narrow versus wide fronts, which helps coordinate this pull with other handles in the same project. The combination of zinc material and brushed nickel finish defines both the underlying metal and surface treatment, which supports matching this pull with other brushed nickel components specified on the same job.

Common Questions About The Fuji 224mm Cabinet Pull

Selecting This Fuji Pull For Cabinet Projects

This R. Christensen by Berenson Fuji Series brushed nickel pull, with its 8-13/16 inch center to center and 12-1/2 inch overall length, gives a defined size for cabinets that call for a larger handle. The zinc material with brushed nickel finish establishes both the base metal and appearance, which fits projects built around brushed nickel decorative hardware. With known projection and width, this 1188-1BPN-C pull from Wurth Baer Supply can be specified wherever these dimensions align with cabinet design and drilling requirements.