Bessey 12" capacity k body parallel clamp kre3512

Bessey 12 Inch K Body Parallel Clamp Use

Bessey 12 inch K Body parallel clamp delivers secure clamping force up to 1,700 lb, so workpieces are held firmly during glue-ups or assembly where slip would throw off alignment. The clamp is designed to clamp at 90 degrees to the rail with very large clamping surfaces, which keeps pressure even across panels or frames and helps reduce twist while joints are pulled tight. An operating jaw that stays where you put it supports quick layout, because the jaw does not slide away while parts are positioned. Three removable pressure caps are resistant to glue, paint and solvents, so dried squeeze-out or overspray does not bond to the contact faces and the clamping surfaces stay usable over repeated jobs.

Key Bessey KRE3512 Features For Woodworkers

• Secure clamping force up to 1,700 lb delivers strong, consistent pressure on joints so panels, doors or frames stay tight during curing and handling.
• Designed to clamp at 90 degrees to the rail with very large clamping surfaces applies force square to the work, helping keep parts flat and reducing racking while closing assemblies.
• Ergonomic two component handle with steel socket for applying force with a hex key or driver when desired (max torque 17 Nm) lets the user bring joints together with less hand strain when higher pressure is required.
• Operating jaw that stays where you put it for easy set up supports one-person positioning of parts, because the clamping head does not drift while stock is aligned.
• Three removable pressure caps are resistant to glue, paint and solvents, so the pads shed residue instead of bonding to workpieces, helping protect finished surfaces.
• Two work piece supports prevent the clamped material from contacting the steel rail, keeping stock off any debris on the rail and reducing marking while pressure is applied.

Clamp Adjustment, Spreading, And Operation Details

The clamp converts to spreading, no tools required, in seconds by removing the end stop and reversing the operating head, which lets the same tool pull assemblies apart or push components into position during fitting. For smooth opening, releasing any clamping pressure in place then pivoting the handle up and away from the rail allows the operating jaw to slide freely, which speeds resetting for the next job. For closing and clamping, pivoting the handle towards the rail, sliding the jaw to the work piece and then beginning clamping brings the pads into contact quickly before final torque is applied with the ergonomic handle or optional hex key or driver.

Using The Bessey K Body Revo Clamp In The Shop

Where This Parallel Clamp Excels In Woodworking

This Bessey Tools clamp sits in the Clamps class under Woodworking Tools and Equipment and Hand Tools, so it is built around holding wood components during typical shop tasks. The 12 inch capacity is suited to narrower panels, face frames, drawer parts and smaller assemblies where a compact bar is easier to maneuver on a bench. Clamping at 90 degrees to the rail with very large clamping surfaces means the tool supports tasks where flatness and squareness are important, such as edge-gluing boards, pulling miters together, or holding case parts in alignment. Two work piece supports keep the clamped material from contacting the steel rail, so finished or prepared faces stay spaced off the bar while glue or finish is present on the job.

Details That Support Repeatable Setups And Results

The operating jaw that stays where you put it for easy set up allows repeatable clamping positions, since the head remains at a chosen opening while parts are loaded, which is helpful when running several identical assemblies. Secure clamping force up to 1,700 lb provides a consistent pressure range from light snugging to high force within the rated limit, helping joints close along their full length. The ergonomic two component handle with steel socket for a hex key or driver (max torque 17 Nm) gives the option of hand tightening or using a driver to reach higher torque when laminating thicker stock. Three removable pressure caps that resist glue, paint and solvents help keep pad faces clean over time, so contact points remain predictable from one glue-up to the next, supporting uniform pressure patterns.

Common Questions About The Bessey KRE3512 Clamp

Select The Bessey KRE3512 For Parallel Clamping

This Bessey 12 inch K Body parallel clamp combines up to 1,700 lb clamping force, 90 degree clamping to the rail, and stable, large clamping surfaces, making it suited to precise panel and frame work. The jaw that stays where you put it, tool-free conversion to a spreader, and ergonomic handle with steel socket for optional hex key or driver give flexibility across many woodworking setups. Selecting this clamp from Wurth Baer Supply aligns a proven Bessey Tools design with everyday shop tasks that demand consistent, square pressure.