Bessey 31 inch capacity K Body parallel clamp brings up to 1,700 lb of secure clamping force, which helps draw joints tight on demanding woodworking glue-ups where consistent pressure is needed along the workpiece. The clamp is designed to clamp at 90 degrees to the rail with very large clamping surfaces, so panels, doors, and assemblies stay flat while pressure is applied across their width. An operating jaw that stays where you put it supports quick, one-person setups, because the movable jaw holds its position while you position parts. The clamp converts to spreading in seconds by removing the end stop and reversing the operating head, allowing the same tool to separate or expand assemblies when a spreading action is required.
The clamp converts to spreading without tools by removing the end stop and reversing the operating head, so switching between clamping and spreading tasks fits into normal shop workflow. For smooth opening, releasing any clamping pressure and then pivoting the handle up and away from the rail allows the operating jaw to slide, which speeds resetting for a wider opening. For closing and clamping, pivoting the handle towards the rail, sliding the jaw to the work piece, and then applying force creates a repeatable sequence, which helps installers and woodworkers follow the same motions on every setup.
The PARALLEL CLAMP KBODY REVO 31 provides 31 inch capacity in a clamp designed to hold at 90 degrees to the rail, which suits edge-gluing boards, clamping casework, or holding door assemblies where squareness matters. Very large clamping surfaces support workpieces across a broad area, so wide panels and frames benefit from even load spread while adhesive cures. Two work piece supports keep the clamped material from contacting the steel rail, which is useful when working with freshly glued or finished parts that you want raised clear of metal surfaces. Three removable pressure caps that are resistant to glue, paint, and solvents let the clamp function in typical shop conditions, so users can clamp parts that have wet glue or finishing products on nearby surfaces.
The Bessey KRE3531 parallel clamp delivers secure clamping force up to 1,700 lb, which supports demanding joints where strong compression down the length of a panel is valuable. The ergonomic two component handle with steel socket for a hex key or driver, used within the max torque of 17 Nm, allows additional leverage when higher force is needed while keeping hand control over the final tightening. An operating jaw that stays where you put it aids repeatable setups, because the jaw position remains fixed until you move it, letting you align stock, then complete clamping without fighting jaw drift. The ability to convert to spreading by removing the end stop and reversing the operating head adds flexibility, so one clamp can handle both drawing parts together and pushing them apart in repair or fitting tasks. The workflow for opening - releasing clamping pressure, pivoting the handle up and away from the rail, then sliding the operating jaw - helps the jaw travel smoothly along the rail, which saves time when resetting between different job sizes.
The Bessey KRE3531 offers 31 inch capacity, which covers many panel, casework, and frame clamping tasks where medium-length reach across the workpiece is required.
The parallel clamp delivers secure clamping force up to 1,700 lb, which supports tight joints on demanding glue-ups and structural assemblies needing strong compression.
The clamp is designed to clamp at 90 degrees to the rail with very large clamping surfaces, which helps assemblies stay square and flat under pressure.
The Bessey KRE3531 converts to spreading in seconds by removing the end stop and reversing the operating head, allowing one tool to handle expansion tasks.
The ergonomic two component handle with steel socket for a hex key or driver, rated to max torque 17 Nm, lets users apply controlled extra force when required.
Three removable pressure caps resist glue, paint, and solvents, and two work piece supports keep material off the steel rail, which supports cleaner, repeatable clamping.
The Bessey KRE3531 parallel clamp combines 31 inch capacity, up to 1,700 lb of clamping force, and very large 90 degree clamping surfaces, which supports accurate panel and frame assembly. With an ergonomic two component handle, steel socket for a hex key or driver at up to 17 Nm torque, and an operating jaw that stays where you put it, the clamp fits repeatable shop workflows. Adding conversion to spreading, removable pressure caps, and work piece supports, this Bessey clamp offers a practical option for woodworking professionals and serious DIY users handling regular glue-ups and assemblies.
Sold In: 1 Each