Hickory Hardware Wire Pull 3-3/4" (96 mm) Center to Center, Satin Nickel, PW596-SN

Hickory Hardware Wire Pulls For Cabinet Projects

Hickory Hardware Wire Pulls gives you a straightforward cabinet pull that suits many decorative hardware jobs. This PW596-SN satin nickel pull uses a 3-3/4 inch (96 mm) center to center layout, so it lines up with a common drilled hole pattern on cabinets and furniture. The pull is made from steel, which provides a solid metal feel under load when doors or drawers are opened and closed repeatedly. Its satin nickel finish offers a muted metallic look that supports a wide range of cabinet colors without drawing excess attention. The pull length of 4-1/16 inch gives fingers a defined gripping area across typical drawer fronts, while the 1-1/4 inch projection creates space behind the wire shape so hands clear the face frame. A 5/16 inch width keeps the profile slim, which helps when installing several pulls across smaller drawer banks.

Key Details That Support Real Cabinet Work

• The 3-3/4 inch (96 mm) center to center drilling matches a widely used layout, which helps when aligning replacement pulls to existing borings on kitchen or bath cabinets.
• The steel material provides a sturdy metal body, which supports repeated opening cycles on active drawers and doors in residential woodworking projects.
• The satin nickel finish delivers a soft metallic look, which works well where a neutral decorative hardware appearance is needed across mixed room finishes.
• The 4-1/16 inch overall length spans typical drawer rail widths, which gives users a comfortable hand placement when pulling heavier drawer loads.
• The 1-1/4 inch projection holds the pull out from the cabinet face, which creates working finger clearance and reduces contact with finished door or drawer surfaces.
• The 5/16 inch width keeps the wire profile narrow, which can be useful when multiple pulls are lined up on smaller fronts where space is limited.

Installation Layout And Dimensional Fit Details

This PW596-SN pull uses a 3-3/4 inch (96 mm) center to center dimension, which lets installers match the pull to standard double-hole drilling on many cabinets. With a total length of 4-1/16 inch, the pull covers the bored area while still leaving visible door or drawer material around the hardware. The 1-1/4 inch projection holds the pull body away from the surface, which helps fingers wrap naturally around the wire form. At 5/16 inch width, the pull presents a slim bar that can be positioned close to adjacent fronts without crowding. The steel construction supports firm tightening against the surface, which helps maintain alignment over time in active use areas.

Using This Belwith Keeler Pull In Projects

Where This 96 Mm Satin Nickel Pull Works

This Belwith Keeler PW596-SN pull sits in the Decorative Hardware & Moldings handles and pulls category, which positions it for cabinet and furniture drawer fronts that call for functional wire-style hardware. The 3-3/4 inch (96 mm) center to center spacing corresponds to a common boring pattern, so it suits situations where existing handles from the Wire Pulls collection or similar layouts are being changed to satin nickel. The satin nickel finish supports installations across kitchens, baths, and storage areas where a consistent metal tone is preferred across several cabinets. Its 4-1/16 inch length allows the pull to sit neatly on door rails or drawer fronts without extending past typical edge clearances, which helps maintain a clean hardware line across a run of cabinets.

Why These Dimensions Help Repeatable Results

The defined 3-3/4 inch (96 mm) center to center dimension gives installers a clear measurement when drilling new cabinet fronts, which simplifies layout work across multiple doors or drawers. Because the overall length is only slightly greater than the drilling span, the PW596-SN provides consistent visual margins at each end of the pull, supporting a uniform look when several pulls are mounted in a row. The 1-1/4 inch projection allows a hand to get behind the wire without contacting the surface, which reduces wear on finished faces as users operate the doors or drawers over time. The 5/16 inch width concentrates the gripping surface, which can aid users in getting a secure hold even when adjacent hardware or trim is close by. Steel construction supports firm torque on the fasteners during mounting, which helps the pull stay square and aligned through regular cabinet use.

Common Questions About The PW596-SN Wire Pull

Choose This 96 Mm Pull For Consistent Layouts

The Hickory Hardware Wire Pulls PW596-SN satin nickel pull brings together a 3-3/4 inch (96 mm) center to center drilling, 4-1/16 inch overall length, and 1-1/4 inch projection to support predictable cabinet layouts. Steel construction and a 5/16 inch wire width provide a compact, sturdy handle that fits many decorative hardware projects. For jobs that call for a Belwith Keeler cabinet pull in satin nickel with a common 96 mm layout, this model from Wurth Baer Supply aligns dimensions and finish for straightforward cabinet and furniture work.