Extruded Aluminum Angles 1 x 12 Mill describe a 1 inch by 1 inch aluminum angle in a 12 foot length that is used for edge protection in many applications, so long edges, corners, and exposed edges can be shielded from damage in a single continuous run. The angle legs are described as metal edge moldings, so the piece serves as a clean, right angle protection and trim where two surfaces meet. The product is identified as ALU ANGLE MOLDING,1'X1'X12FT,MILL FINISH and as Extruded Aluminum Angles 1 x 12, Mill, so buyers get a defined size and surface condition for layout and fabrication. Dimensions in the table below are all outside dimensions, so cuts and adjoining materials can be sized to the external profile of the angle rather than estimating from interior measurements.
This aluminum edge molding is identified as a 1 inch by 1 inch angle in a 12 foot length, so it provides a full length right angle profile suitable for running along long edges that need continuous protection. The mill finish designation means the surface reflects the as-extruded aluminum condition, so shops can treat it as a base finish suitable for further finishing processes or leave it as is where a standard aluminum appearance is appropriate. Since legs of all stock angles are 1/8 inch thick, cut plans and mating material thickness can be coordinated around that fixed leg dimension during layout and fabrication. Being part of metal edge moldings, the product is oriented toward applications where the aluminum angle defines both the physical protection and the visual termination of an edge.
This product is described as Extruded Aluminum Angles 1 inch x 12 feet, Mill and as ALU ANGLE MOLDING,1'X1'X12FT,MILL FINISH, so it is suited to straight edges that match a 1 inch by 1 inch right angle profile. Because it is used for edge protection in many applications, it can be applied anywhere a 1 inch outside dimension aluminum corner is needed along a panel, countertop edge, or similar straight run. As part of metal edge moldings, it functions well wherever an exposed edge benefits from both mechanical protection and a defined metal corner line. With all dimensions noted as outside dimensions, the molding is suited to jobs that depend on precise external fit, such as aligning with panel faces or adjacent trim.
The fact that legs of all stock angles are 1/8 inch thick gives a predictable thickness for every leg of the 1 inch by 1 inch angle, which supports consistent saw setups, notching, and alignment where the molding meets adjoining materials. Since all are stocked in 6 foot and 12 foot lengths, installers can select length runs that match common project spans, limiting field joints along long edges and helping maintain a continuous protective surface. The mill finish on the Extruded Aluminum Angles 1 x 12 Mill provides a uniform as-extruded aluminum surface that can be incorporated into visible edges where a standard aluminum look is acceptable or prepared for further finishing processes. Because dimensions in the table below are all outside dimensions, layout based on the full external profile reduces guesswork when aligning the angle with panels, frames, or other edge elements.
The molding is identified as ALU ANGLE MOLDING,1'X1'X12FT,MILL FINISH, so each leg is 1 inch, the length is 12 feet, and it forms a right angle for edge protection.
Legs of all stock angles are 1/8 inch thick, providing a consistent leg thickness that simplifies aligning the molding with adjoining materials and planning cuts or notches.
Dimensions in the table below are all outside dimensions, so the stated 1 inch by 1 inch size refers to the external profile, which helps with precise edge fit and layout.
The product is described as Mill Finish, so the surface reflects the as-extruded aluminum condition that can be integrated visually or prepared for further finishing steps.
The product is used for edge protection in many applications, so its 1 inch by 1 inch right angle profile shields corners and exposed edges from impact along straight runs.
All are stocked in 6 foot and 12 foot lengths, so layouts can be based on shorter or longer continuous pieces, supporting fewer joints along protected edges.
This Dave Sanders and Company extruded aluminum angle is identified as a 1 inch by 1 inch by 12 foot metal edge molding with mill finish, so it lines up well with projects that call for a defined aluminum right angle along exposed edges. Because it is used for edge protection in many applications and all stock angle legs are 1/8 inch thick with outside dimensions called out, it fits directly into shop drawings and on-site layouts that depend on predictable dimensions. For projects that need a straightforward aluminum edge molding solution, this 1 inch by 1 inch, 12 foot mill finish angle provides a clearly defined profile for planning and execution.
Sold In: 1 Each