Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Jet Tools 708595 JSG-96 benchtop sander combines a 9 inch disc and a 6 inch x 48 inch belt into one machine, so a shop can handle both face sanding and edge work on the same tool for efficient workflow. The benchtop layout keeps this sander compact on the bench, which helps in smaller shops where floor space is tight but material size still demands solid sanding capacity. Its industrial 3/4 HP motor provides the power to handle tough sanding operations, letting the user remove stock and clean up edges without overworking the machine. The sander uses a single phase 115V power supply, fitting typical shop electrical service so it can be placed where the work happens. This design gives woodworking operations a single, dedicated station for flattening, shaping, and general cleanup.
The JSG-96 runs on single phase 115V power, which ties directly to common shop circuits and simplifies placing the sander near benches or assembly areas. Built-in handles make the benchtop unit easier to move, so it can be positioned where workflow needs it or stored when not in use. A large cast iron table provides a solid work surface, helping support parts during sanding for steadier control. That table has preset stops at 90 degrees and 45 degrees, letting the operator set up reliable angles without repeated measuring. These preset stops allow the belt sander to be used vertically, horizontally, or anywhere in between, so the same machine can handle different part orientations and sanding approaches as jobs change.
The combination of a 6 inch x 48 inch belt and 9 inch disc means the JSG-96 handles a range of sanding tasks, from truing edges on the belt to cleaning up end grain or small parts on the disc, all at one station. Its industrial 3/4 HP motor is designed to easily handle the toughest sanding operations, so it suits workloads that involve solid wood, frequent stock removal, or continuous shaping. The large cast iron table supports workpieces at the disc and benefits from preset stops at 90 degrees and 45 degrees, giving repeatable angle setups for miters, chamfers, or square sanding. Because the belt can run vertically, horizontally, or at positions in between, the sander can be configured for face sanding panels, easing edges, or sanding to layout lines along taller parts. A single 4 inch dust port on the back provides a connection point for dust collection, helping direct sanding debris away from the work zone for better visibility and a cleaner machine surface during use.
The drive drum on the JSG-96 is rubber-coated, which increases grip on the sanding belt and cuts down on belt slippage, giving more consistent belt speed and more uniform scratch patterns across the work. Exclusive dual thumbscrew belt tracking adjustment lets the operator fine-tune belt position and then lock it, so the belt stays on track during use and keeps its alignment across repeated passes. The graphite covered steel platen under the belt runs cooler, which helps manage heat at the sanding interface, supporting longer belt life and steadier performance on heat-sensitive surfaces. A quick-release belt tension lever speeds belt changes, which encourages swapping grits as needed instead of stretching one belt too long, improving surface quality across stages. The quick-lock dust cover that allows fast disc changes makes it practical to move from heavier-grit setup discs to finer finishing discs as parts move through the sanding sequence.
The JSG-96 benchtop sander combines a 6 inch x 48 inch belt with a 9 inch disc, letting one machine handle edge sanding, face sanding, and small-part work in a single station.
The JSG-96 sander uses a powerful 3/4 HP motor that easily handles the toughest sanding operations, supporting steady stock removal without bogging under typical woodworking loads.
The JSG-96 benchtop sander runs on single phase 115V, so it works with common shop electrical service and can be positioned near standard bench outlets.
The JSG-96 has exclusive dual thumbscrew belt tracking adjustment that locks, keeping the belt on track during use and supporting consistent alignment along the platen.
The graphite covered steel platen on the JSG-96 runs cooler, which helps extend machine and belt life while maintaining smoother operation during prolonged sanding.
The large cast iron table on the JSG-96 has preset stops at 90 degrees and 45 degrees, giving repeatable angle positions for square sanding and common beveled cuts.
The JSG-96 Benchtop 6 x 48 belt and 9 inch disc sander from JET Tools brings industrial 3/4 HP power, a single phase 115V motor, and a compact benchtop footprint together for practical shop use. Its large cast iron table with preset 90 degree and 45 degree stops, graphite covered steel platen, and exclusive dual thumbscrew belt tracking adjustment give tradespeople controlled, repeatable sanding setups. With quick-release belt tension, quick-lock disc access, a rubber-coated drive drum, and a single 4 inch dust port, this machine is built to support steady workflow on sanding tasks.
