Sliding Door Track Assembly No. 15, 5' Length Oil Rubbed Bronze

Sliding Door Track Assembly No. 15 For Glass

Sliding Door Track Assembly No. 15 is an EPCO aluminum sliding door hardware set designed for 1/4 inch thick glass doors, so it gives glass panels a defined running path in a single track layout. The 5 ft long aluminum track length suits many cabinet, wardrobe, or partition openings where a straight, continuous glide is needed across that span. The oil rubbed bronze finish presents a dark, uniform appearance over the aluminum, which supports projects calling for bronze-toned exposed hardware. The assembly is identified as manufacturer part number 15-ORB-5, so it can be referenced consistently across ordering, planning, or repeat jobs. This assembly is described as sliding door hardware and builders hardware, so it is intended to function as a guided slide system rather than a pivot or hinge point. The product is packed and sold in each unit, which supports specifying one complete assembly per sliding opening.

Track Assembly Details That Support Daily Use

• The aluminum 5 ft long track gives 1/4 inch thick glass doors a straight running surface, so the panel travels consistently across the opening over that full span.
• The oil rubbed bronze finish on the aluminum track presents a dark bronze tone, so visible hardware aligns with designs built around bronze or similar finishes.
• The 730 upper guide component in the assembly provides a defined top constraint for the glass door, so the panel stays aligned along the upper edge during movement.
• The 726 single track sections in the assembly establish the linear path for the sliding door panels, so the rollers have a consistent channel to follow as the door moves.
• The 752 rollers in the assembly carry the weight of the glass door along the track, so the door can travel along the length of the aluminum track with guided motion.
• The 771 clip guides work with the track and rollers to restrain the glass panels laterally, so side-to-side play is reduced as the door slides.

Sliding Track Mounting And Door Height Planning

The aluminum track assembly is 5 ft long, so installers can plan the opening width and support points around that single-piece length. For glass height, the description states to deduct 1-7/16 inch from the opening height, so the installed glass panel height is sized to clear the track and running hardware within the framed opening. The assembly is designed for 1/4 inch thick glass doors, so glass selection and channel details can be matched to that thickness. This track system is identified as sliding door hardware, so it expects a configuration where the glass panel moves laterally within the opening rather than swinging out. Mounting screws are referenced, so the track and related components are fastened in place for fixed alignment over time.

Using This EPCO Sliding Hardware In Projects

Where This Sliding Door Track Assembly Fits Best

This EPCO Sliding Door Track Assembly No. 15 is described for 1/4 inch thick glass doors, so it suits applications where glass panels act as the moving closure, such as glass-front cabinets, display cases, or similar openings with framed supports. The 5 ft long aluminum track lets one continuous assembly span an opening of similar width, so it is useful where a single straight run is preferred over shorter joined sections. As sliding door hardware within builders hardware, it is adapted to structures where the supporting frame can receive a track base and upper guiding elements for glass. The oil rubbed bronze finish allows this track assembly to coordinate with other bronze-toned components in the same installation, so exposed rails and guides can visually match nearby bronze hardware.

How Track Components Support Repeatable Sliding Motion

The presence of a 730 upper guide, 743 shoes, 726 single track, 730 track base, 752 rollers, and 771 clip guides in the assembly defines a complete path for the 1/4 inch thick glass panels, so the door runs within a matched set of guidance points rather than relying on a single element. The 730 track base provides a foundation for the single track sections, so the track is supported and located along the mounting surface in a controlled way. The 743 shoes relate to how the glass panels engage with the track and guides, so the interface between the glass and moving hardware is organized through those parts. The glazing vinyl in the assembly supports the contact between the 1/4 inch glass and its holding components, so the panel is cushioned where it seats within the hardware. Together, these elements define the sliding path, contact points, and constraints for the glass door, so movement along the aluminum 5 ft long rail can remain guided and consistent over repeated use.

Common Questions About EPCO Track Assembly No. 15

Select This Track Assembly For 1/4 Inch Glass Runs

This EPCO Sliding Door Track Assembly No. 15 brings together a 5 ft long aluminum oil rubbed bronze track, guides, rollers, shoes, track base, clip guides, glazing vinyl, and mounting screws for 1/4 inch thick glass doors. With the glass height set by deducting 1-7/16 inch from the opening height, the assembly defines the relationship between opening size and glass panel size. For projects calling for sliding door hardware that matches this 5 ft span, glass thickness, and oil rubbed bronze finish, this assembly provides a coordinated track and guidance system ready to be specified by part number 15-ORB-5.