Sliding Door Track Assembly No. 15, 6' Length Oil Rubbed Bronze

Sliding Door Track Assembly No. 15 For Glass

Sliding Door Track Assembly No. 15 gives installers a complete aluminum sliding track setup for 1/4 inch thick glass doors in one coordinated system. The 6 foot long aluminum construction creates a continuous track run, so glass panels move along a stable, uniform path from end to end. The oil rubbed bronze finish provides a dark, uniform appearance that supports jobs where visible hardware needs a consistent look across multiple openings. The design for 1/4 inch thick glass doors means the hardware interfaces directly with that glass thickness, keeping the doors supported in the track without improvised shims or adapters. The EPCO branding and 15-ORB-6 part reference clearly identify this track assembly in project documents, which helps repeat the same hardware choice across similar openings on a job.

Key Sliding Track Details For Glass Doors

• The 6 FT long aluminum track length spans typical cabinet or small opening widths, allowing longer uninterrupted movement of 1/4 inch thick glass doors across the opening.
• The track assembly is designed specifically for 1/4 inch thick glass doors, so the contact components support that glass thickness for predictable engagement and smooth sliding.
• The oil rubbed bronze finish on the aluminum components delivers a dark, consistent color tone, helping hardware visually coordinate with other oil rubbed bronze elements in the same area.
• The EPCO Sliding Door Track Assembly No. 15 designation and 15-ORB-6 part number give installers a clear reference, simplifying ordering, documentation, and repeat use on future projects.
• Aluminum construction provides a continuous formed track structure over the 6 foot length, supporting aligned roller and guide movement along the full span of the opening.

Sliding Door Track Installation And Fit Details

This EPCO sliding door track assembly uses aluminum single track and a coordinating track base to establish the sliding path for 1/4 inch thick glass doors, so the mounting surface receives a matched upper and lower rail arrangement. The glazing vinyl in the system works with the 1/4 inch thick glass doors, helping the glass sit correctly in its holding components during installation. Upper guides, clip guides, and rollers interface with the aluminum track sections, which organizes the installation around fixed reference points instead of improvised alignments. Mounting screws are part of the system design, so the track, base, and guides fasten directly to the supporting structure using fastening locations intended for this assembly.

Using This Sliding Door Track Assembly On Projects

Where This EPCO Track Assembly Fits Best

This EPCO sliding door track assembly is built for 1/4 inch thick glass doors, so it serves projects where glass panels of that thickness need to slide within a 6 foot opening. The aluminum 6 FT long single track sections and track base define the top and bottom travel for the doors, which is useful on installations where glass needs a controlled, linear path. The upper guide marked as 730 works with the aluminum track to guide the door at the top, helping the panel follow the intended line of movement. The 743 shoes interface between the glass and the track system, providing a defined contact point for the glass doors along the running gear. The 752 rollers carry the glass doors along the track profile, so the door movement follows the formed aluminum path from side to side. The 771 clip guides work with the track and rollers to maintain door position, supporting consistent tracking along the aluminum sections. Glazing vinyl in the system works with the 1/4 inch thick glass doors to help the glass seat into its holding components, which is important when fitting multiple panels to a shared opening.

Details That Support Smooth, Repeatable Door Travel

The Sliding Door Track Assembly No. 15 organizes several matched components around a 6 foot aluminum track length, so installers work from a coordinated group of parts rather than unrelated pieces. The 730 upper guide and 730 track base reference the same system design, which helps align top and bottom paths so door movement stays parallel across the entire opening. The two 726 single track sections in aluminum create defined linear channels for the 752 rollers, so each door travels along a fixed route shaped specifically for this assembly. The four 752 rollers distribute movement points along the doors, which helps the doors track consistently across the 6 FT span when the rollers engage the aluminum sections. Four 771 clip guides interface with the track and shoes, helping keep the 1/4 inch thick glass doors in proper relation to the running gear during use. The glazing vinyl matches the 1/4 inch glass door application to support how the glass is captured in the shoes or related holding components, which matters when repeating door setups on multiple similar openings.

Common Questions About EPCO 15-ORB-6 Track

Select Sliding Door Track Assembly No. 15 For 1/4 Inch Glass

The EPCO Sliding Door Track Assembly No. 15 in oil rubbed bronze aligns a 6 FT aluminum track, 1/4 inch glass compatibility, guides, rollers, glazing vinyl, and mounting screws into a single system. For projects calling for this configuration, this assembly lets installers match finish, glass thickness, and sliding hardware layout to the specified opening.