Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Cuff flange for 1 inch tubing describes an EPCO closed flange designed for 1 inch and 1-1/16 inch closet tubing, so it supports standard round rods used in closet and storage runs. The closed flange design, as stated, surrounds the tubing, which helps hold the rod in position at the end or support point. The part mounts with a back plate, so the visible face keeps the installation simple and clean in finished closets. Because this EPCO flange is listed in the Closet Rods & Flanges product class, it works in typical shelf, closet, and garage organization layouts where round tubing carries hanging loads. The product is identified as EPCO 855-DC, so matching the part number to drawings or existing hardware is straightforward on repeat jobs. The dull chrome description defines the visible finish, aligning the flange with other dull chrome closet components on a project.
The description states that this cuff flange screws on to a back plate, so installation begins by positioning and fastening that plate to the support surface where the rod terminates. Once the plate is set, the closed aluminum cuff flange threads or screws to the back plate, so the installer locks the part in line with the mounted base without exposing working fasteners on the face. The product note that it mounts invisibly means the fastening points sit behind the flange body, which keeps the visible dull chrome exterior uninterrupted across the front. With a 30mm length, the installed flange sets the rod seat a consistent distance from the wall, so mirrored flanges at each end hold the tubing parallel to vertical panels or walls across the span.
The brand line identifies EPCO as the maker, and the manufacturer part number 855-DC marks this specific dull chrome cuff flange, so it can be specified directly on closet and storage drawings. The category Shelf, Closet & Garage Organization and the product class Closet Rods & Flanges place this part in typical clothes-hanging and storage tube runs, so it works at rod ends or intermediate supports wherever 1 inch or 1-1/16 inch tubing is used. Because the web description calls it a closed flange for 1 inch and 1-1/16 inch tubing, it seats round closet rods in those sizes, keeping the tube captured inside the cuff at wall or panel terminations. Aluminum construction, as stated, suits interior closet and cabinet environments where a light but stable flange body is appropriate around standard tubing. The dull chrome finish coordinates with dull chrome closet tubing and brackets, supporting consistent appearance across visible hardware points.
The stated 30mm length sets how far the flange body extends from the mounting back plate, so the rod seat repeats at the same offset whenever 855-DC flanges are used along a project, supporting straight, level rod lines. The description that the cuff flange screws on to the back plate means the installer first locks in plate location, then brings the visible flange on, which helps preserve measurement and layout marks even if the front piece is adjusted during alignment. Since the mounting is described as invisible, the working fasteners stay behind the aluminum cuff, so there are no exposed screw heads on the dull chrome face to interrupt finished closet aesthetics. The product name specifically calling out 1 inch and 1-1/16 inch tubing clarifies the intended tubing diameters, so selecting this flange for those rod sizes keeps the fit controlled inside the closed cuff. Listing the part under Closet Rods & Flanges signals its role as a structural support point for hanging tubes, so it can be used in pairs at each end of a run or with matching center supports where the same tubing runs across longer spans.
The Epco 855-DC cuff flange is described as a closed flange for 1 inch and 1-1/16 inch tubing, so it is intended to seat standard round closet rods in those two diameters.
The cuff flange screws on to a back plate and mounts invisibly, so fasteners sit behind the aluminum cuff while the dull chrome face presents a clean, finished appearance.
The Epco 855-DC cuff flange is specified as aluminum with a dull chrome description, giving a light metal body with a subdued chrome look at visible closet rod supports.
The flange is listed under Shelf, Closet & Garage Organization and Closet Rods & Flanges, so it is used at rod ends or supports on 1 inch and 1-1/16 inch closet tubing.
The 30mm length identifies how far the flange body extends from the mounting back plate, helping installers maintain a consistent rod offset from the wall along a run.
The cuff flange screws on to the back plate, so the installer positions and fastens the plate first, then attaches the flange, helping preserve rod alignment with the layout marks.
The web description defines this EPCO 855-DC part as a closed aluminum cuff flange for 1 inch and 1-1/16 inch tubing, so it is set up for standard closet rods. Its 30mm length and invisible screw-on back plate connection support consistent, clean-looking installations across closet or garage organization projects. For jobs calling for dull chrome closet rods in these diameters, this cuff flange offers a matching EPCO component that seats the tubing and hides mounting points while keeping layout dimensions predictable from one location to the next.
Sold In: 1 Each