2-3/8" Diameter x 34-1/2" High Rockwell Single Table Leg, Aluminum Silver
Description
Rockwell Single Table Leg For Stable Work Surfaces
Rockwell single table leg delivers a 2-3/8 inch diameter support that resists wobble under a work surface, so installers can build solid tables and counters with a clean, minimal footprint. The 34-1/2 inch height sets the leg for table projects where a consistent finished height is important across multiple units. An aluminum silver finish provides a neutral, professional look that blends with a wide range of tops, which helps projects match existing shop, office, or residential layouts. The leg is part of the Rockwell line from Peter Meier, Inc., tying directly to a known table leg system for repeat jobs and replacement work. As a single leg, it can be used to support corners, overhangs, or intermediate points, so layouts can be tailored to each installation without over-building the base.
Key Rockwell Single Table Leg Work Advantages
- The 2-3/8 inch diameter round leg provides a compact footprint while still giving broad contact at the floor, which supports stable work surfaces without bulky framing under the top.
- The 34-1/2 inch overall leg height sets a predictable starting point for table height, helping installers line up multiple work surfaces in the same room or along a run.
- The aluminum silver finish presents a clean, uniform appearance that suits many commercial and residential spaces, which simplifies matching visible legs across different projects.
- The leg is identified as part of the Rockwell line from Peter Meier, Inc., so repeat orders can follow the same specification when a job calls for additional or replacement legs.
- The product is classified under work surface and table legs, supporting its role as a primary structural support component rather than decorative trim.
Mounting Plate And Adjustable Foot Details For Install
The 4 9/16 inch square mounting plate gives a broad connection area to the underside of the work surface, which spreads load and helps reduce stress at the fastener locations. A 1 1/8 inch adjustable foot at the base allows small height corrections, which is useful when floors are uneven or when multiple legs must share load without rocking. The mounting plate and foot work together so the leg can be set plumb under the top while keeping contact tight at the floor, supporting a solid feel on finished tables or counters.
Using This Aluminum Silver Table Leg On Projects
Where This Rockwell Single Table Leg Fits Best
This Rockwell single table leg is described for table, counter, and bar heights, so it supports a range of work surface applications from standard tables to higher standing surfaces. The aluminum silver color works with many laminate and wood tops, helping installations maintain a consistent visual line across open spaces. Because the leg is sold as a single unit, it can be positioned exactly where support is needed under longer tops, such as mid-span positions or outer corners. The work surface and tables classification aligns it with shop benches, office tables, and similar structures where metal legs are preferred over panel bases. With the 2-3/8 inch diameter tube carrying load down to an adjustable foot, the leg can be set to share weight with walls, cabinets, or additional legs along the run.
Why The Adjustable Foot And Plate Support Accuracy
The 1 1/8 inch adjustable foot provides fine height control under the 34-1/2 inch leg, which helps bring multiple legs to the same effective height and tighten the top against the mounting plate. This adjustment range lets installers compensate for floor variation without cutting the leg, saving time on layout and reducing rework. The 4 9/16 inch square mounting plate creates a generous footprint at the top of the leg, giving room to place fasteners toward the edges of the plate for better pull-out resistance. With the plate sized at 116 mm square, the load from the work surface is spread over a wider area, which is important under heavier tops. Together, the plate and adjustable foot help keep the work surface level over time by supporting even load sharing and straightforward re-adjustment during service work.
Common Fit And Use Questions For This Table Leg
What is the height of this Rockwell single table leg?
The Rockwell single table leg is 34-1/2 inches high, which sets it up for table projects and helps align multiple work surfaces to the same finished height.
How wide is the table leg at the floor contact point?
The table leg has a 2-3/8 inch diameter, so the floor contact area is compact while still offering a solid, stable base for the work surface above.
What does the 1 1/8 inch adjustable foot do on this leg?
The 1 1/8 inch adjustable foot lets you fine-tune the leg height to accommodate uneven floors so the work surface stays level and solid.
How large is the mounting plate on this table leg?
The mounting plate is 4 9/16 inches square, giving a broad attachment area under the work surface to spread load and support secure fastening.
What finish and material does this Rockwell leg use?
The Rockwell leg is aluminum in a silver finish, providing a neutral, professional look that coordinates with many work surface materials and colors.
Who manufactures this 34-1/2 inch aluminum table leg?
This 34-1/2 inch aluminum silver table leg is produced by Peter Meier, Inc., tying it to an established Rockwell table leg line for ongoing projects.
Select This Rockwell Leg For Precise Surface Support
The 34-1/2 inch height, 2-3/8 inch diameter tube, and 4 9/16 inch square mounting plate give this Rockwell single table leg a clear role as a primary support for work surfaces. The aluminum silver construction and 1 1/8 inch adjustable foot help projects achieve both alignment and appearance goals on tables, counters, and bar-height runs. For jobs centered on metal legs under laminate or wood tops, this Peter Meier, Inc. Rockwell leg offers a repeatable specification that can be used across initial builds and follow-up installations.