Olympus Lock, Inc Offset Cam 1-1/2" Length - PL39001

Combi-Cam 7440 Cam For Secure Lock Operation

Combi-Cam 7440 cam is a 1-1/2 inch hook cam designed for use with Combi-Cam 7440 locks, so it serves as the working arm that engages the strike on these combination locks. The cam is described as a straight cam, which means its profile follows a direct line from the mounting point to the hook, helping the lock throw feel predictable when the lock is turned. Length is defined as the distance from the center of the mounting hole to the top of the cam, giving a clear reference for how far the hook will reach past the cylinder in a lock assembly. This specific geometry matters when matching the cam to an existing Combi-Cam 7440 setup, because the throw length and reach affect how reliably the lock secures doors, drawers, or panels built around this lock family.

Key Details That Support Lock Alignment

• 1-1/2 inch hook cam length, measured from the center of the mounting hole to the top of the cam, sets a defined throw distance that helps align the cam reach with the strike or catch in a Combi-Cam 7440 installation.
• Hook cam design allows the cam end to wrap around or catch behind a mating surface, helping the Combi-Cam 7440 lock pull a door, drawer, or panel into a held position when the lock is actuated.
• Straight cam construction provides a direct path from the mounting hole center to the hook, supporting consistent rotation behavior around the mounting hole and helping installers predict how the cam will swing through its arc.
• 1/4 offset identified in the description defines how the cam is displaced relative to the lock centerline, which affects how the cam lines up with strikes in different overlay or inset layouts that use the Combi-Cam 7440 lock body.

Cam Length And Offset For Practical Fit

The 1-1/2 inch length, defined from the center of the mounting hole to the top of the cam, gives installers a fixed dimension to design around when laying out Combi-Cam 7440 lock locations. By using a hook cam sized this way, the throw can be matched to typical door or drawer clearances that suit the Combi-Cam 7440 body. The 1/4 offset stated in the description shows that the cam face is shifted relative to the mounting hole center, influencing how far the cam sits from the lock axis once tightened. This offset helps adapt the same lock body to different panel positions by altering the cam reach path while keeping the rotation centered on the mounting hole.

Using This Olympus Lock Cam In The Field

Where This 1-1/2 Inch Hook Cam Fits

The 1-1/2 inch hook cam for use with Combi-Cam 7440 locks is built specifically around that lock family, so it slots into installations that rely on Combi-Cam 7440 combination-style hardware. Because Olympus Lock, Inc. identifies this part as a straight cam with a defined length from the center of the mounting hole to the top of the cam, it is suited to lock layouts where the geometry of the throw has already been based on the Combi-Cam 7440 pattern. The 1/4 offset described in the SAP information allows the cam to sit off the direct axis of the lock, which helps it reach strikes located slightly forward or back from the cylinder face in typical cabinet, drawer, or panel constructions that use this lock class. Within these layouts, the hook shape lets the cam engage a strike surface behind an edge, so the cam can hold the panel once rotated into position.

Why Length, Offset, And Hook Shape Matter

The defined 1-1/2 inch length, measured from the center of the mounting hole to the top of the cam, matters because it directly controls how far the cam will extend past the Combi-Cam 7440 lock body when rotated, affecting how securely the lock engages its mating point. By specifying that this Olympus Lock, Inc. part is a hook cam, the product ensures the end of the cam curves or bends to catch behind a strike, which can provide a more positive hold than a flat-ended piece when the lock rotates through its travel. The straight cam description indicates that the cam follows a simple, direct profile as it extends from the mounting hole to the hook, making its path of rotation around the mounting hole easier to visualize when positioning strikes in the same plane. The 1/4 offset given in the product description further refines this path by shifting the cam relative to the lock axis, which can help align the hook with differently positioned cabinet faces while still using the same Combi-Cam 7440 lock cylinder location.

Common Questions About The PL39001 Cam

Selecting This Cam For Combi-Cam 7440 Locks

The Olympus Lock, Inc. PL39001 1-1/2 inch hook cam pairs directly with Combi-Cam 7440 locks, giving a defined length from the center of the mounting hole to the top of the cam for consistent throw geometry. With its straight cam profile, hook end, and 1/4 offset described in the product data, this part offers a specific reach path tailored to the lock family. For projects built around Combi-Cam 7440 combination locks, choosing this cam part number aligns the lock body, cam throw, and strike position to the same dimensional standard.