Amerock self-close 3/8 inch inset hinge is a semi-concealed face frame hinge designed for 3/8 inch inset cabinet doors, so the door sits partially inside the frame while still showing a controlled reveal. This self-close action pulls the door shut at the end of travel, which helps doors seat consistently without relying on a push every time. The semi-concealed face frame design leaves only part of the hinge visible, giving traditional face frame cabinets a cleaner look while still allowing access for adjustments and service. This Amerock Corporation hinge is part of a functional hardware series that is tested for durability in conditions exceeding KCMA certification requirements, so it is built for repeated daily use on working cabinets. Testing beyond BHMS standards for cycle life, strength and finish quality supports long-term performance on high-use doors in kitchens, shops or similar environments.
This Amerock semi-concealed face frame hinge is built specifically for face frame cabinets, so it locates directly on the frame rather than inside a frameless box. The 3/8 inch inset detail defines the relationship between the door edge and the frame, guiding layout when matching hinges across a run of cabinets. As a screw-on hinge, it relies on screw fastening through the hinge plates into the cabinet material and door, giving a fixed, repeatable mount once positioned. The partial wrap configuration stabilizes the hinge on the frame edge, which supports consistent door swing along the full cycle tested under Amerock functional hardware series standards.
This Amerock BPR7565FB hinge is a semi-concealed face frame hinge, so it is suited to cabinets built with a face frame rather than a frameless box. The 3/8 inch inset specification aligns with doors that recess 3/8 inch into the opening while still covering part of the frame, a layout commonly used on traditional residential and shop cabinetry. Because it is a partial wrap hinge, it positions around part of the frame edge, giving the door a defined pivot point on that face frame. The self-close function is valuable anywhere doors are opened and closed frequently, because the hinge pulls the door into contact at the end of travel for a consistent shut position. Amerock identifies this hinge within a functional hardware series tested in conditions exceeding all KCMA certification requirements, so it is built with the demands of active cabinet environments in mind.
Every Amerock functional hardware series item, including this self-close partial wrap hinge, is tested for durability in conditions exceeding all KCMA certification requirements, which means it is evaluated beyond common kitchen cabinet performance benchmarks. This testing covers areas like cycle life and strength, so repeated opening and closing is assessed to support long-term hinge function on busy cabinet runs. Amerock also states that testing exceeds BHMS standards for cycle life, strength and finish quality, tying performance directly to both mechanical movement and surface finish. In practice, this verified attention to finish quality on the flat black hinge surface helps the hinge retain its appearance through repeated handling around the door edge. The combination of self-close function, partial wrap support on the face frame and Amerock durability testing supports consistent alignment and motion for cabinet doors over many operating cycles.
The Amerock self-close 3/8 inch inset semi-concealed hinge is designed for face frame cabinets, so it mounts to a cabinet frame rather than a frameless side panel.
The 3/8 inch inset specification means the cabinet door sits 3/8 inch inside the frame opening, guiding door sizing and frame layout when using this hinge.
The self-close function on this Amerock hinge pulls the door shut at the end of travel, helping doors land in a consistent closed position against the frame.
Semi-concealed face frame hinge means part of the hinge remains visible on the face frame while the working mechanism is hidden, balancing access and appearance.
Amerock testing in conditions exceeding KCMA requirements and BHMS standards evaluates cycle life, strength and finish quality, supporting dependable cabinet door performance.
Partial wrap indicates the hinge wraps around part of the face frame edge, helping stabilize the door connection and support repeatable swing motion.
The Amerock Corporation self-close 3/8 inch inset semi-concealed face frame hinge in flat black ties hinge function, appearance and test-backed durability into one part for face frame cabinets. The partial wrap design, self-close action and 3/8 inch inset layout all work together to control how the door sits and moves on the frame. Because this Amerock functional hardware series hinge is tested for durability in conditions exceeding all KCMA certification requirements and BHMS standards, it supports long-term cabinet door service where cycle life and finish quality matter. For cabinet runs calling for flat black functional hardware with a defined 3/8 inch inset relationship, this Amerock BPR7565FB hinge provides a clearly specified option.