Peter Meier Hanging Bracket w/Safety Lock, Right Hand, Dowel Mount, 704-ZV-DX

Hanging Bracket With Safety Lock For Wall Cabinets

hanging bracket with safety lock describes a steel, nickel plated bracket designed to support wall cabinets as part of a wall hanging rail system, so installers can mount cabinetry using a compact component that is built around a defined application. The right hand configuration matches layouts that call for handed hardware on each cabinet side, so planning rail runs and bracket positions stays consistent from cabinet to cabinet. The 704 series designation and manufacturer part number 704-ZV-DX tie this bracket to a specific Peter Meier, Inc. hanging system, which matters when matching components on repeat jobs or service work. A slim design lets the bracket sit with minimal projection, helping cabinets sit close to the wall while still providing access to the adjustment ranges. The bracket is sold in each quantities, which supports ordering only the counts needed for a given run of wall cabinets.

Key 704 Series Bracket Details For Projects

• The steel, nickel plated finish creates a hard metal surface that supports cabinet loads while presenting a neutral appearance inside wall cabinets or behind cover caps where a finished hardware look matters.
• The 340 lbs. weight capacity per pair defines how much load two brackets can carry, allowing the installer to match cabinet and contents weight to the rated support for standard wall cabinet applications.
• The 10mm dowel mount interface locates the bracket in predrilled holes, which helps position the hardware consistently and speeds cabinet production or on-site drilling setups that follow the same pattern.
• The right hand orientation aligns this bracket with one side of a wall cabinet in a handed hanging rail system, so left and right positions remain clear during installation and later adjustment work.
• The depth adjustment range of 12mm gives front-to-back movement at the cabinet connection, helping align door reveals and cabinet faces along a run when walls are not perfectly straight.
• The height adjustment range of 19mm allows vertical tuning of the cabinet position, which is useful for leveling adjacent wall cabinets and matching lines to ceilings or trim.

Dowel Mount And Adjustment Details For Installers

The 10mm dowel mount on this Peter Meier, Inc. 704 series bracket sets the cabinet interface to a common drilling size, letting installers use standard 10mm boring tools when preparing the cabinet side. The right hand layout defines which cabinet side this bracket serves, so the pair arrangement remains predictable during layout. A depth adjustment range of 12mm provides front-to-back cabinet movement relative to the hanging point, which helps fine-tune face alignment against neighboring units or wall surfaces. The 19mm height adjustment range gives up-and-down movement at the hanging connection, so the cabinet can be leveled after hanging without re-boring or shifting the rail position. The integrated safety lock screw detail adds a locking function at the bracket, which helps keep the cabinet secured on the rail once final position is set.

Using The 704 Series Hanging Bracket In Wall Runs

Where This Right Hand Bracket Fits Best

This Peter Meier, Inc. hanging bracket with safety lock is identified as part of a wall hanging rail system, so its role is to connect wall cabinets to that system using a defined hardware interface. The 704 series naming and part number 704-ZV-DX tie it directly to other 704 components, which supports consistent hardware selection on full kitchen or shop wall runs. As a right hand, 10mm dowel mount part, it fits on the designated side of the cabinet that uses 10mm dowel bores for mounting, providing secure placement into the cabinet body. The slim design keeps the bracket compact inside or behind the cabinet, leaving space for interior use while maintaining clearance for door hardware and shelving adjustments. A steel, nickel plated finish supports typical cabinet environments by providing a sturdy, metal-based connection at the hanging point that integrates cleanly with modern cabinet hardware.

Why These Adjustment And Safety Details Matter

The specified 340 lbs. weight capacity per pair sets a concrete performance value for two brackets, which lets installers assign these to wall cabinets that fall within that load, such as standard kitchen or storage cabinets. Depth adjustment of 12mm allows the cabinet body to be nudged in or out after hanging, giving control over how the cabinet face aligns along a continuous run and against finished wall surfaces. Height adjustment of 19mm at the bracket means the cabinet position can be raised or lowered slightly without moving the rail, which helps correct minor level and plumb issues quickly. The safety lock screw mentioned for this hanging bracket adds a mechanical locking step once alignment is complete, reducing the chance of cabinet shift during normal use. When combined, these details let installers hang, adjust, and secure wall cabinets as part of a 704 series wall hanging rail system using a single, defined right hand component.

Common Questions About The 704-ZV-DX Hanging Bracket

Selecting This 704 Series Bracket For Wall Cabinets

The Peter Meier, Inc. 704-ZV-DX hanging bracket with safety lock pairs a 10mm dowel mount, right hand layout, and 704 series identification to support precise hardware matching on wall cabinet projects. The 340 lbs. weight capacity per pair, steel nickel plated finish, and defined 12mm depth plus 19mm height adjustment ranges provide clear performance and alignment details when planning a wall hanging rail system. For wall cabinet installations that call for a right hand 704 series component, this hanging bracket offers a defined set of mounting and adjustment characteristics to match the rail-based layout.