Bainbridge Manufacturing 2-7/8" (73 mm) Center to Center Brown Recessed Pull - 1710BR-32

Bainbridge Manufacturing Recessed Pull For Clean Access

Bainbridge Manufacturing recessed pull provides a compact hand grip that sits down in the surface, so doors or panels present a cleaner face while still opening easily. This 1710 Series brown recessed pull uses a 2-7/8 in center to center size, which sets the screw spacing and helps match layouts using that dimension. The pull is made from plastic in a brown finish, so the color runs with many wood tones and non-metal installations where metal is not required. The overall length of 3-5/8 in gives enough grab area while keeping the pull tight to smaller drawer or door fronts. A projection of 1 in sets how far the grip stands off the mounting surface, which affects finger clearance and snag potential in tight areas. The recessed design relies on a mortise, so the pull sits low in the panel for a more streamlined installation.

Key 1710 Series Details For Daily Use

• The 2-7/8 in center to center dimension fixes the mounting hole spacing, which simplifies drilling patterns when repeating this brown recessed pull across multiple fronts.
• The 3-5/8 in overall length defines how much linear space the pull occupies, which helps when laying out several pulls on a narrow cabinet or matching existing trim lines.
• The 1 in projection sets the stand-off from the surface, giving consistent fingertip clearance while limiting how far the pull extends into walk-by zones.
• The 1-1/2 in width establishes the transverse footprint, which matters when routing the pocket and when checking clearances near panel edges or adjacent hardware.
• The plastic construction with brown finish provides a non-metallic option, useful where a lighter-weight pull and brown color are preferred over exposed metal hardware.
• The 1710 Series designation ties this pull to that specific Bainbridge Manufacturing line, aiding part identification when matching or replacing existing units.

Recessed Pull Mounting Dimensions And Fit

This Bainbridge Manufacturing 1710 Series recessed pull uses a mortise hole of 3-1/8 in, which sets the cutout length needed in the panel for the body to sit properly. With a 1-1/2 in width, the routed pocket must match that dimension, helping the pull register square without side play. The 2-7/8 in center to center layout determines where mounting fasteners land relative to the mortise opening, affecting how the pull bears load in the panel. A projection of 1 in defines how the hand fits behind the grip once mounted, which matters on thinner doors or drawer fronts. The pull is specified with a #6 sheet metal screw size, so the mounting holes and pilot holes are sized to work around that screw diameter in typical sheet material.

Using This Brown Recessed Pull In Projects

Where This 1710BR-32 Recessed Pull Fits Best

This Bainbridge Manufacturing 2-7/8 in center to center brown recessed pull works in applications that benefit from a low-profile grip set into the surface rather than on top of it. The 3-5/8 in length and 1-1/2 in width make it suitable for modest-size doors or drawer fronts where space is limited yet a clear handhold is still needed. A mortise hole of 3-1/8 in defines the pocket size, so any project using this pull is based around that opening for a consistent look across multiple fronts. The brown finish helps this plastic recessed pull blend with darker panels or edge-banded components where a matching tone is desired. With the 1710 Series designation and 1710BR-32 part number, projects that already use this line can keep visual continuity by repeating the same style.

Details That Support Repeatable Recessed Pull Results

The 2-7/8 in center to center spacing on this 1710BR-32 recessed pull supports consistent layouts, since drilling jigs or CNC programs can reference that single value for the mounting holes. A mortise hole length of 3-1/8 in gives a clear target for routing templates, which helps the pull seat flush in every opening. The 1 in projection works as a fixed design value, so installed pulls share the same stand-off and hand clearance from door to door. With a 1-1/2 in width, installers can balance setback from panel edges while still maintaining sufficient material around the routed pocket. The specified #6 sheet metal screw size helps standardize hole sizing and grip strength in typical sheet goods. Together, these defined dimensions let shops repeat the same brown recessed cabinet pull across runs of cabinets or fixtures with predictable fit and appearance.

Common Questions About The 1710BR-32 Recessed Pull

Select This Recessed Pull For Defined Dimensions

This Bainbridge Manufacturing recessed pull from the 1710 Series combines a 2-7/8 in center to center layout, 3-5/8 in length, and 3-1/8 in mortise requirement to give clear installation targets. The brown plastic construction and 1 in projection support low-profile cabinet or panel designs needing a recessed handhold. For projects built around known dimensions and repeatable setups, this 1710BR-32 recessed pull offers a consistent pattern that aligns with the stated measurements.