Bainbridge Recessed Pull 2-7/8" (73 mm) Center to Center, Gray, 1710GY-32

Bainbridge Gray Recessed Pull For Clean Grip

Bainbridge gray recessed pull is a 2-7/8 in center to center handle designed to sit in a recess, so the grip stays low profile while still being easy to grab on cabinets or panels. The pull is part of the Bainbridge Manufacturing 1710 Series, which gives you a consistent look and geometry across similar installations, helpful when matching existing hardware on a run of doors. The gray finish keeps the pull visually quiet, which suits workspaces, utility cabinetry, and projects where hardware should not dominate the surface. The pull is made from plastic, so it keeps weight down on lightweight doors or drawer fronts while still providing a defined finger pocket. With a 3-5/8 in length, the pull spans enough surface to feel secure in the hand, yet stays compact for tight layouts or narrow faces.

Key Bainbridge 1710GY-32 Details For Projects

• The 2-7/8 in (73 mm) center to center dimension sets consistent fastener spacing, which simplifies layout when drilling multiple doors or aligning with existing holes.
• The 3-5/8 in overall length gives a little edge clearance beyond the screw points, which helps distribute pull force across more of the cabinet surface.
• The 1 in projection keeps the pull low profile off the face, useful where doors pass close to walls or adjacent cabinets yet still need finger access.
• The 1-1/2 in width provides a stable bearing surface, which can reduce localized stress on the mortise area of the door or drawer front during repeated use.
• The mortise hole size of 3-1/8 in defines the recess cutout, allowing a snug fit that helps the pull sit flush and keeps the installation looking intentional.
• The gray plastic material coordinates with neutral interiors and work environments while resisting visual wear better than more reflective finishes in high-touch areas.

Recessed Pull Fit, Mortise Layout, And Mounting

This Bainbridge Manufacturing recessed pull is specified with a 3-1/8 in mortise hole, so the installer can size the routed or cut opening to support a flush, supported fit. The 2-7/8 in center to center measurement works within that mortise dimension, giving clear reference points for drilling through-holes or setting fasteners in line with the recess. With a 1-1/2 in width, the pull covers the mortise edges, which helps mask minor variations in the cut and keeps the visible perimeter clean. A 1 in projection defines how far the grip stands proud of the surface, guiding alignment in relation to neighboring doors, drawers, or frames. The pull is identified by manufacturer part number 1710GY-32, which ties this exact size, series, material, and gray finish together when specifying parts for new work or replacements.

Using This Gray Plastic Pull In Real Jobs

Where This 2-7/8 Inch Pull Works Well

The Bainbridge Manufacturing 2-7/8 in center to center gray recessed pull works well where a low profile grip is needed on cabinet doors, drawers, or panels that still need confident hand access. The recessed design pairs with the 3-1/8 in mortise hole, so the body sits within the door thickness, reducing the chance of catches in narrow aisles or along tool paths. Its 3-5/8 in overall length and 1-1/2 in width let it land comfortably on standard cabinet rails or stiles without dominating the face, which suits utility cabinets and shop storage. The gray plastic material coordinates with common neutral casework and laminate colors, so the pull can blend into institutional, workshop, or back-of-house environments while maintaining a consistent 1710 Series appearance.

Details That Support Consistent Cabinet Results

On repeat installations, the 2-7/8 in (73 mm) center to center spacing allows jigs or templates to be reused, which supports faster drilling and consistent alignment across multiple fronts. The defined 3-1/8 in mortise hole dimension gives a target for routing or machining, helping maintain a uniform pocket size that keeps each pull seated similarly. With a 1 in projection, door swing clearances and drawer passes can be planned once and repeated, reducing trial-and-error on site-built cabinetry. The 3-5/8 in length and 1-1/2 in width create a familiar hand feel from unit to unit, useful when matching existing Bainbridge Manufacturing 1710 Series layouts. The plastic gray construction keeps the hardware and cabinet mass relatively light, which can be helpful on thinner fronts or large banks of doors where weight adds up.

Common Questions About The 1710GY-32 Pull

Select The 1710GY-32 Pull For Consistent Layouts

The Bainbridge Manufacturing 1710GY-32 gray plastic recessed pull combines a 2-7/8 in center to center spacing with a defined 3-1/8 in mortise hole, supporting repeatable cabinet layouts. With its 3-5/8 in length, 1-1/2 in width, and 1 in projection, the pull balances a compact footprint with practical hand access. The gray finish and 1710 Series identity help align this pull with existing Bainbridge hardware choices. For projects needing a low profile recessed grip with predictable dimensions, this part number keeps the hardware selection straightforward.