Patwin 288 Beige T-Molding, 250' L x 13/16" W - 7/64" Kerf - P500-13/16-288

Beige Tee Molding For Curved Or Straight Edges

beige tee molding from Patwin Plastics is a non-toxic polyethylene molding designed to finish and protect edges on woodworking and similar projects. The Flexene construction lets this tee molding fit outside or inside curves and radii, so one profile can follow various cabinet or panel shapes. The product is consistently precise in dimensions, workability, and color, which helps runs look uniform from start to finish and supports clean, repeatable machining. The design of this molding ensures the installation will fit firmly and hug edges permanently, giving a secure fit after the kerf is cut to the specified size. The 13/16 inch width works with compatible edge layouts where that face dimension is needed. A 250 ft length per roll supports longer production runs or multiple projects from a single roll.

Key Flexene Tee Molding Details For Projects

• Non-toxic polyethylene construction is used to manufacture these Flexene moldings, which provides an edge treatment option made from this specific material for woodworking environments.
• The molding fits any contour whether outside or inside curves and radii, allowing one profile to follow sweeping curves, tight radii, or straight edges on cabinets or panels.
• The product is consistently precise in dimensions, workability, and color, helping installers maintain an even reveal, steady feed through equipment, and consistent appearance from piece to piece.
• The design ensures the installation will fit firmly and hug edges permanently, so once set into the 7/64 inch kerf the molding stays seated along the edge profile.
• The tee molding is supplied in 250 ft rolls, so each roll supports extended runs on jobs requiring continuous edge treatment over many linear feet.
• The product is sold in full rolls only, in both broken and full box quantities, so ordering is based on complete 250 ft lengths for planning linear footage needs.

Installation Fit And Kerf Details For Use

This Patwin Plastics tee molding uses a 7/64 inch kerf, so the cut in the substrate must match that dimension for the stem to seat properly. When the kerf matches the 7/64 inch requirement, the molding design allows it to fit firmly and hug the edge, supporting a permanent hold once pressed into place. The 13/16 inch width covers the edge and adjacent face area to that dimension, which is useful when layouts call for that specific coverage. Flexene construction lets the molding follow outside or inside curves and radii, so the same installation method applies around corners and along straight runs. The 250 ft roll length provides continuous material for feeding through cutting or notching setups when preparing lengths for installation.

Where This Patwin Tee Molding Works Best

Tee Molding Application On Curves And Straight Runs

This Patwin Plastics, Inc. P500-13/16-288 tee molding is part of the Edgebanding & Surfacing and Tee Moldings product class, so it is suited to edge treatment tasks in woodworking-related settings. Non-toxic polyethylene is used to manufacture these Flexene moldings, giving a profile designed for these types of edge finishing applications. Because the molding fits any contour whether outside or inside curves and radii, it can follow cabinet sides, counter edges, or similar components that shift from straight sections into curves. The 13/16 inch width provides a defined coverage band along the edge, while the consistently precise dimensions support uniform kerf engagement along both simple and complex shapes. In continuous runs, the 250 ft roll length makes it practical to handle long edges without frequent material changes.

Details That Support Consistent, Permanent Edge Results

The design of this Flexene tee molding ensures the installation will fit firmly and hug edges permanently when pressed into a 7/64 inch kerf, which supports long-term edge performance once installed. Consistently precise dimensions, workability, and color reduce variation as pieces are cut and applied, which is important when multiple panels must match within a project. The polyethylene material works with the Flexene profile so the molding can bend smoothly around curves without disrupting the fit in the kerf. The 250 ft roll length lets installers cut specific segments while still drawing from a single, continuous coil, helping maintain color consistency across many parts. Patwin Plastics, Inc. branding and the P500-13/16-288 part number identify this exact tee molding profile for repeat ordering when the same edge detail is required again.

Common Questions About P500-13/16-288 Tee Molding

Select This Beige Tee Molding For Edge Projects

This Patwin Plastics P500-13/16-288 beige tee molding combines non-toxic polyethylene material, a 13/16 inch width, and a 7/64 inch kerf design to support dependable edge treatment. Flexene construction lets it fit outside or inside curves and radii, while consistently precise dimensions and color help finished work look uniform. With 250 ft rolls sold in full rolls only and discount available for full box orders, this tee molding suits both single projects and repeated production runs.