Kitchen Kompact Glenwood sink base is a 30 inch wide, 34-1/2 inch high, 24 inch deep base cabinet built for standard kitchen sink runs where a recessed panel style is specified. The cabinet belongs to the Kitchen Kompact Glenwood line, so it keeps projects consistent where that series is already planned. The frame is built of solid 3/4 inch oak, maple, or beech, which carries load around the sink opening and supports countertop weight in typical kitchen layouts. Each rail in the frame is kiln-dried, which stabilizes the wood before machining and helps the frame stay true while the cabinet is handled and set. Rails are joined by mortise and tenon and then glued, creating mechanical interlock plus adhesive bond so the face frame resists racking during transport, leveling, and daily door use around a busy sink area.
This Glenwood 30 inch sink base is 30 inches wide, which matches common layout modules and simplifies planning between adjoining base units. The 34-1/2 inch height fits standard kitchen base lines, setting up a typical finished counter height when paired with standard countertop thickness. A 24 inch depth matches standard base cabinet depth, allowing the sink base to align flush with neighboring bases and with typical appliance depths. The recessed panel design on the Glenwood face integrates with the broader Glenwood style, so the sink position does not interrupt the visual run. Solid wood hanging strips at both the top and bottom edges of the base cabinet give installers defined fastening zones when tying the unit into the wall and to neighboring cabinets.
The Glenwood 30RBS sink base is used in kitchen cabinet runs where a 30 inch wide base is planned under a sink location, and the Glenwood recessed panel style is specified. The solid 3/4 inch wood frame around the front opening supports sink-front doors and trim pieces while holding a consistent reveal with adjacent Glenwood cabinets. Solid wood corner blocks, glued and power nailed, brace the cabinet box at each corner so the base stays square when it is pulled into line with other bases. End panels built with 3-ply construction and a 1/2 inch engineered wood core with hardwood veneers provide stable finished sides when the sink base terminates a run or sits against an opening. Solid wood toe kicks, 3/4 inch thick, carry the cabinet load down to the floor at the front, supporting the section where users typically stand during sink work.
On this Kitchen Kompact GW30RBS cabinet, each frame rail is kiln-dried, then joined by mortise and tenon and glued, so the joints resist loosening and support consistent door alignment over time. Solid wood hanging strips on base cabinets, located at the top and bottom, run along the back, creating continuous fastening zones that help pull the cabinet tight to the wall and hold it there under countertop load. Solid wood corner blocks, glued and power nailed, link the rails and sides so the cabinet maintains its geometry when clamped to neighboring units. The 3-ply end panels, with a 1/2 inch engineered wood core and hardwood veneers, reduce the tendency for side panels to move with seasonal changes, supporting straighter seams where sink bases meet other cabinets. Solid 3/4 inch wood toe kicks at the front also contribute to rigidity at floor level, supporting shims and contact points along the length of the sink base.
The Glenwood sink base is 30 inches wide, 34-1/2 inches high, and 24 inches deep, so it fits standard kitchen base cabinet layouts and typical countertop depth and height.
The face frame is built of solid 3/4 inch oak, maple, or beech, providing a substantial front structure for mounting doors and supporting everyday sink cabinet use.
The frame rails are kiln-dried, joined by mortise and tenon, and then glued, creating stable joints that help maintain door alignment and resist racking during service.
End panels use 3-ply construction with a 1/2 inch thick engineered wood core and hardwood veneers, giving stable, flat sides that finish cleanly next to other cabinets.
Solid wood hanging strips on base cabinets, located at the top and bottom, run along the back to provide solid fastening areas for securing the sink base to the wall.
The 3/4 inch thick solid wood toe kicks form a sturdy front base area that carries cabinet load to the floor and supports shims along the sink work zone.
The Kitchen Kompact Glenwood sink base GW30RBS delivers a 30 inch wide, 34-1/2 inch high, 24 inch deep cabinet sized for standard sink locations, with a solid 3/4 inch wood frame that ties into the rest of a Glenwood run. Kiln-dried, mortise-and-tenon, glued rails, solid wood corner blocks, and 3/4 inch solid wood toe kicks create a rigid box ready to carry countertop and daily sink traffic. Solid wood hanging strips and 3-ply end panels with a 1/2 inch engineered wood core with hardwood veneers support a straight, stable installation in typical kitchen cabinet layouts.
Sold In: 1 Each