Kitchen Kompact Warmwood sink base cabinet WW33RBS is a 33 inch wide cabinet designed as a sink base at 34-1/2 inch height and 24 inch depth, so it fits a standard kitchen sink run while keeping counter height and cabinet depth consistent across the line. The Warmwood sink base uses maple flat panel doors, which provide a flat recessed panel look that matches the Warmwood style across the Kitchen Kompact line for a unified appearance. Door frames are mortised and tenoned construction of solid 3/4 inch maple, creating a mechanically locked corner joint that supports repeated daily use on an active sink cabinet. Solid wood corner blocks are glued and power nailed, tying sides and face together so the base holds square when installed in a run of cabinets. Solid wood hanging strips located on the top and bottom give solid attachment points during wall fastening, helping maintain alignment along the back.
This Warmwood 33 inch wide sink base is sized at 34-1/2 inch high and 24 inch deep, so it works in standard kitchen layouts where base cabinets align under typical countertops. Solid wood hanging strips located on the top and bottom give defined fastening zones across the back, which helps hold the cabinet in plane with neighboring units during alignment. Solid wood corner blocks are glued and power nailed, so the box stays square while it is adjusted on shims or leveled along an uneven floor. Solid wood toe kicks at 3/4 inch thick form a sturdy front base section that supports applied toe boards and helps carry vertical loads down to the floor across the cabinet front.
The Kitchen Kompact Warmwood sink base cabinet is designed as a 33 inch wide base at 34-1/2 inch height and 24 inch depth, so it functions as the central sink location in a typical base cabinet run. Maple, flat panel doors give the Warmwood recessed panel style, letting this cabinet visually align with other Warmwood base and wall units in the same kitchen. Adjustable shelves inside the cabinet offer flexible storage positions, so cleaning supplies or kitchen items can be set at practical heights around plumbing voids. The flat panel plywood insert is a three-ply panel with a rotary cut hard maple veneer face, giving a maple-grain center panel that visually ties to the maple door frames for coordinated Warmwood fronts. Solid wood toe kicks, 3/4 inch thick, extend across the front lower section, letting the cabinet stand as part of a continuous base line under countertops.
Door frames use mortised and tenoned construction of solid 3/4 inch maple, which creates precise joints that help doors hang true on concealed, self-closing hinges over the life of the kitchen. Concealed, self-closing hinges keep hardware out of sight when doors are closed and pull doors fully shut, which supports consistent reveals and clean face lines on a sink base that is opened frequently. Solid wood corner blocks that are glued and power nailed tie the cabinet box together, so when the cabinet is set, leveled, and fastened through the solid wood hanging strips located on the top and bottom, the structure helps maintain alignment. Plywood drawers are standard, and the front to back epoxy-coated drawer system is securely attached to a solid wood strip in the back of the cabinet, so drawer movement runs along a guided track that leverages the solid rear attachment for stable slide operation. A 4 step process of stain, sealer, sanding and catalyzed top coat is applied, building a layered finish over the Warmwood maple veneer and solid maple that supports color consistency and surface protection across the kitchen installation.
The Kitchen Kompact Warmwood sink base WW33RBS measures 33 inches wide, 34-1/2 inches high, and 24 inches deep, so it fits standard base cabinet height and depth in most kitchen layouts.
The Warmwood sink base doors use door frames with mortised and tenoned construction of solid 3/4 inch maple, providing strong, interlocking joints at the corners where hinges and pulls load the frame.
The Warmwood sink base uses concealed, self-closing hinges so doors close fully and hardware stays hidden, creating clean front lines and consistent closing action during frequent sink-area use.
The Warmwood sink base receives a 4 step process of stain, sealer, sanding and catalyzed top coat, giving the maple surfaces a finished layer sequence that supports color and surface performance.
The sink base has plywood drawers standard, and the front to back epoxy-coated drawer system is securely attached to a solid wood strip in the back of the cabinet for stable drawer slide support.
The Warmwood sink base cabinet has adjustable shelves, allowing shelf heights to be set around plumbing or stored items so the under-sink space can be arranged for practical daily access.
The Kitchen Kompact Warmwood sink base cabinet WW33RBS combines a 33 inch wide, 34-1/2 inch high, 24 inch deep footprint with maple flat panel doors and a Warmwood finish system, so it aligns visually and dimensionally in standard kitchen runs. Mortised and tenoned solid 3/4 inch maple door frames, solid wood corner blocks that are glued and power nailed, and solid wood hanging strips located on the top and bottom give this base a structural core suited to an active sink location. For projects using Warmwood recessed panel styling, this sink base provides the dedicated sink position that ties storage, toe space, and front appearance together along the cabinet line.
Sold In: 1 Each