Kitchen Kompact Glenwood sink base delivers a 42 inch wide ADA compliant cabinet that supports sink runs where accessible height is required, so you can plan handicap-friendly layouts around a defined footprint of 42 inches wide, 32-1/2 inches high, and 24 inches deep. The Glenwood cabinet design uses oak, flat panel doors over a recessed panel style, which creates a consistent Glenwood look that ties in with matching pieces across the same Kitchen Kompact line. Door frames use mortised and tenoned construction in solid 3/4 inch maple, so each corner joint is built as an interlocking frame that helps the doors stay square when mounted and adjusted. A flat panel plywood insert with a three-ply panel and a rotary cut hard maple veneer face fills each frame, which gives a stable panel that resists typical door warping while keeping a maple appearance on the face.
This Glenwood ADA sink base cabinet is sized at 42 inches wide, 32-1/2 inches high, and 24 inches deep, so layout work can be planned around these fixed case dimensions when placing adjacent cabinets and appliances. Solid wood hanging strips at the top and bottom of the back panel provide continuous, solid zones for fastening into studs or structural backing, which supports a straightforward installation sequence across the run. Solid wood toe kicks at 3/4 inch thick form the lower front face of the cabinet, so floor transitions and trim can be aligned to a consistent, solid base edge. The cabinet uses plywood drawers with a front to back epoxy-coated drawer system that ties into a solid wood strip at the rear, which keeps drawer motion controlled from the front face back to the cabinet interior during mounting and final adjustment.
The Glenwood ADA sink base with its 42 inch width, 32-1/2 inch height, and 24 inch depth fits into base cabinet runs where an ADA compliant sink location is needed, so clearances and counter heights can be planned around these case dimensions. Oak, flat panel doors define the Glenwood style across the front of the cabinet, which supports a consistent door appearance when this unit is installed next to other Glenwood pieces from Kitchen Kompact. The recessed panel design uses a flat panel plywood insert as a three-ply panel with a rotary cut hard maple veneer face, giving the front a hard maple veneer look within the oak door framing. Adjustable shelves inside the cabinet can be set at different positions, so storage areas can be tuned to match plumbing layouts or the specific items that need to be kept below the sink. Plywood drawers extend the usable storage inside the 24 inch deep case, allowing smaller tools or supplies to be organized within the same cabinet footprint.
The solid maple door frames are built with mortised and tenoned construction in 3/4 inch stock, which creates defined joints that help doors stay square as hinges are set and final reveals are dialed in. Concealed, self-closing hinges are used on the doors, so the hinge hardware stays out of sight when the doors are closed while helping the doors return consistently to the same position after each use. Solid wood corner blocks that are glued and power nailed tie the cabinet box together at the corners, which supports stable alignment across the case during leveling and fastening into place. Solid wood hanging strips at the top and bottom of the cabinet back serve as continuous structural rails, so fasteners pass through solid wood when the cabinet is pulled tight to the wall. The four step process of stain, sealer, sanding, and catalyzed top coat builds a layered finish over the wood surfaces, which supports color consistency and surface durability throughout everyday kitchen activity. The front to back epoxy-coated drawer system is securely attached to a solid wood strip in the back of the cabinet, creating a defined track that guides drawer travel smoothly from the face frame back into the cabinet interior. Solid wood toe kicks at 3/4 inch thick provide a sturdy front base section that visually anchors the cabinet once it is leveled and aligned with adjacent units.
The Glenwood ADA sink base measures 42 inches wide, 32-1/2 inches high, and 24 inches deep, so cabinet runs, appliance gaps, and countertop lengths can be laid out around a known base footprint.
The doors use mortised and tenoned solid 3/4 inch maple frames with a three-ply flat panel plywood insert, giving each door a strong frame-and-panel build that supports long-term alignment and appearance.
This Kitchen Kompact cabinet uses concealed, self-closing hinges, so the hardware stays hidden when the doors are shut while providing a consistent closing action on every use.
The cabinet uses an epoxy-coated drawer system running front to back and secured to a solid wood strip at the rear, which stabilizes drawer travel all the way into the cabinet interior.
The Glenwood ADA sink base has adjustable shelves and plywood drawers, allowing interior spaces to be set for plumbing, cleaning supplies, or tools within the 24 inch deep cabinet box.
The Glenwood cabinet receives a four step process of stain, sealer, sanding, and catalyzed top coat, building up a finished surface suited to typical kitchen environments.
The Kitchen Kompact Glenwood sink base ADA compliant cabinet combines defined dimensions of 42 inches wide, 32-1/2 inches high, and 24 inches deep with solid wood and plywood construction, so layout, fastening, and alignment all tie back to a stable case. Mortised and tenoned solid maple door frames, a three-ply flat panel plywood insert with hard maple veneer, and solid wood corner blocks create a cabinet box built for regular use in working kitchens. Concealed, self-closing hinges, adjustable shelves, and the epoxy-coated drawer system secured to a solid wood rear strip all support predictable operation once the cabinet is set in a run. For projects built around the Glenwood style and ADA sink locations, this GWH42RBS unit provides the defined Glenwood look and construction details from Kitchen Kompact.
Sold In: 1 Each