Omega National AG-100 appliance garage is a straight, solid wood appliance garage set designed to organize countertop appliances while keeping them covered when not in use. The 30 inch wide size gives room for common kitchen countertop appliances without extending into adjacent cabinet openings. The straight design allows it to align with standard wall cabinets in a run, so installers can keep a clean, continuous front line along the upper cabinets. The appliance garage is part of Omega National Products AG-100 Series, so it fits into a coordinated line of appliance garages and tambour products. Because it is part of a specific product class for appliance garages and tambour doors, it serves both as storage and as a movable front closure in one assembly.
The AG-100SSM-30 appliance garage relies on an 18-3/4 inch high frame housing, so installers can plan vertical clearances knowing the opening height and overall presence under wall cabinets. The two 11 inch wide by 19 inch high end panels give defined side boundaries for the opening, which helps determine where to position the garage on the countertop or cabinet base. The tambour door is designed around a spring tension track system, providing smooth, non-binding operation, so the door can be moved repeatedly during daily use without jerky starts or stops. Because the closing mechanism is already assembled into the frame that houses the tambour door, installation focuses on positioning and fastening the unit rather than building the door assembly from separate door and track components.
The Omega National AG-100 Series appliance garage in the 30 inch width is sized to align with a 30 inch cabinet module, so it can sit directly below a 30 inch wall cabinet to keep visual lines consistent. The 18-3/4 inch high solid wood frame creates a recognizable appliance bay under the wall cabinet, turning a portion of the countertop into a defined appliance station rather than general open counter space. Because the product is categorized as a kitchen and bath cabinet appliance garage, it is intended for locations where small countertop appliances are stored behind a movable front, allowing the same counter section to act as both storage space and active work surface. The straight configuration, rather than a corner-specific shape, suits linear wall runs, giving designers a predictable element when planning standard kitchen layouts.
The frame housing the tambour door with an assembled closing mechanism means the movement of the door has already been designed around a specific spring tension track system, so the track and spring work together to deliver smooth, non-binding travel during opening and closing. That smooth action is important where the door may be cycled many times each day, because consistent motion helps prevent abrupt stops that can affect alignment over time. The two 11 inch wide by 19 inch high veneer faced 3/8 inch thick MDF end panels give each side a uniform surface paired with a stable MDF core, so the sides can visually coordinate with the solid wood frame while providing flat, stable faces for the appliance bay. With the straight appliance garage form and defined panel sizes, installers know the side-to-side and top-to-bottom limits of the unit, which helps when fitting it between existing cabinets or aligning it over a section of countertop dedicated to appliance storage.
The AG-100SSM-30 uses an 18-3/4 inch high solid wood frame, which sets the vertical opening and helps align the appliance garage below standard wall cabinets.
This AG-100SSM-30 model is a 30 inch wide appliance garage, so it matches a 30 inch cabinet module and defines the horizontal space available for storing appliances.
The tambour door is designed around a spring tension track system, providing smooth, non-binding operation as the door opens and closes across the appliance bay.
The sides use two 11 inch wide by 19 inch high veneer faced 3/8 inch thick MDF end panels, creating stable, uniform side walls for the appliance space.
The frame houses the tambour door with an assembled closing mechanism, so the moving parts are built into the frame, simplifying the task of positioning the unit in a cabinet run.
This model is part of Omega National Products AG-100 Series within the appliance garages and tambour doors product class, supporting coordinated use in kitchen cabinet layouts.
The Omega National AG-100 appliance garage in the AG-100SSM-30 model gives a 30 inch wide, 18-3/4 inch high solid wood frame housing a spring tension tambour door, so the appliance bay is clearly sized and operates smoothly. With two veneer faced 3/8 inch thick MDF end panels defining the sides, the unit sets stable boundaries for a dedicated countertop appliance station. For projects calling for a straight, framed appliance garage with an integrated tambour door system, this AG-100 Series model delivers a matched assembly ready to be integrated into kitchen cabinet runs.
Sold In: 1 Each
