12 Inch Solid Surface Saw Blade For Clean Cuts

12 inch solid surface saw blade describes this A.G.E. Series circular saw blade designed for cutting double-sided plastic laminate, plexiglass up to 1/4 inch thick, and solid-surface materials. The 12 inch diameter gives reach and capacity for common countertop and panel work, so sheets and blanks can be processed without multiple passes. An 84 tooth layout works with the solid-surface application to produce fine edges, which helps limit sanding and edge cleanup on finished parts. The 30mm arbor size defines the machine interface, so the blade seats properly on table saws or similar equipment built for this bore. As part of the Amana A.G.E. Series, the 612841-30 model is positioned for woodworking and solid-surface shops that cut engineered surfacing materials regularly.

Key Saw Blade Details For Solid-Surface Work

• The 12 inch diameter provides cutting capacity for typical solid-surface and laminate panels, which supports full-depth cuts on many countertop and panel layouts.
• The 84 tooth configuration is designed for these materials and helps create smoother edges, which reduces rework on cut solid-surface and laminate parts.
• The 30mm arbor bore matches machines built for that spindle size, so the blade can run centered and balanced on compatible table or radial arm saws.
• The triple chip (TC) grind is specified for this blade and is suited to plastic laminate, plexiglass, and solid-surface, helping control chipping at the cut line.
• The 0 degree hook angle is matched to table saws and radial arm and similar type machines, which supports controlled feed and helps keep cuts manageable in solid-surface materials.

Mounting And Hook Geometry For Controlled Cutting

The blade is suitable for table saws and radial arm and similar type machines due to its 0 degree hook angle. This neutral hook geometry influences how the teeth enter the workpiece, supporting a controlled feed rate on fixed or sliding setups. For double-sided plastic laminate, this helps the blade track the material instead of pulling aggressively, which is important for keeping laminate edges intact. On radial arm saws, the 0 degree hook angle is specified to work with the machine design, supporting straight, predictable travel along the arm during crosscuts or sizing cuts in solid-surface or plexiglass up to 1/4 inch thick.

Using This 612841-30 Blade In Shop Workflow

Where This Solid Surface Saw Blade Fits Best

This A.G.E. Series 12 inch diameter blade is described for cutting double-sided plastic laminate, plexiglass up to 1/4 inch thick, and solid-surface materials such as Dupont Corian, Wilsonart, Gilbralter, SSV, and Fountainhead. That application range places the blade in solid-surface and laminate fabrication shops processing countertop blanks, wall panels, and similar components. Using a single blade across these engineered materials lets operators move between solid-surface sheets and laminate panels while staying within the specified use. Suitability for table saws and radial arm and similar type machines means the same blade can be assigned to a main rip or panel saw and to a radial arm saw for crosscut or rough dimensioning work on these materials.

Details That Support Consistent Solid-Surface Results

The triple chip (TC) grind used on this blade is specified for cutting double-sided plastic laminate, plexiglass, and solid-surface materials, so the tooth geometry is matched to hard, man-made surfaces. This grind pattern helps distribute the cutting load across alternating tooth shapes, which supports edge quality on brittle laminates and plexiglass up to 1/4 inch thick. The 84 tooth count works with the TC grind to deliver a finer finish, which matters when edges on Corian, Wilsonart, or similar solid-surface trades are later joined or shaped. The 0 degree hook angle is called out as a reason the blade is suitable for table saws and radial arm and similar type machines, so its cutting behavior is aligned with those saw types in solid-surface workflows. The 12 inch diameter and 30mm arbor specification define the saws that can carry this blade, keeping the 612841-30 positioned as a shop blade for solid-surface and laminate cutting.

Common Questions About The 12 Inch Solid Surface Blade

Select This Blade For Solid-Surface And Laminate Cuts

The Amana A.G.E. Series 612841-30 brings a 12 inch diameter, 30mm arbor, 84 tooth count, triple chip grind, and 0 degree hook angle together for cutting double-sided plastic laminate, plexiglass up to 1/4 inch thick, and specified solid-surface brands. Those details place this circular saw blade as a focused option for table saws and radial arm and similar type machines in shops working regularly with solid-surface and laminate materials. For projects built around Corian, Wilsonart, Gilbralter, SSV, Fountainhead, or comparable solid-surface, this blade aligns with that material list and saw type combination for daily cutting tasks.