Knape And Vogt 12 Inch Over Travel Drawer Slides

Knape and Vogt 12 inch over travel drawer slides use the KV 8405 Series side mount design to support ball-bearing movement, so drawers open and close with controlled travel that suits cabinet and drawer construction work. The 1 inch over-travel feature lets the drawer extend beyond its nominal length, giving better access to items stored in the back of the drawer during everyday use or shop tasks. Side clearance of 1/2 inch plus 1/32 inch, minus 0 each side defines the working space between cabinet and drawer, helping builders size drawer boxes to a predictable gap. A height of 1-13/16 inch sets the vertical space these slides occupy, which matters when fitting into tight cabinet layouts with stacked drawers or shallow clearances. The 32 mm pattern support ties into 32 mm system drilling, so shops using line boring equipment can mount these slides in a familiar hole layout.

Working Details That Support Precise Drawer Builds

• The 1 inch over-travel detail allows the drawer to extend past the front of the slide length, which makes the rear of the drawer easier to reach during loading, unloading, or inspection tasks.
• Side clearance of 1/2 inch plus 1/32 inch, minus 0 each side sets a defined gap, helping builders size drawer widths so the slide engages smoothly without excessive play during installation and operation.
• The slide height of 1-13/16 inch gives a fixed vertical profile, which helps in planning stack spacing for multiple drawers and in fitting slides alongside other cabinet hardware within limited side-wall height.
• The 32 mm pattern reference aligns with system 32 drilling, so production shops running line-bored cabinets can integrate these slides into existing drill patterns without reworking basic hole spacing.
• The lever disconnect feature allows the drawer member to separate from the cabinet member at the lever, which streamlines installing or removing drawers during assembly, finishing, or later service work.
• The ball retainer latch helps hold the ball bearings in place within the slide, which matters for maintaining smooth motion when the slide is cycled repeatedly in service.
• Polymer stop cushions contact at the end of travel, softening the stop of the moving member, which can reduce harsh impact when the drawer reaches its fully open or closed position during normal use.
• The non-handed designation means either slide can mount on either side of the drawer, which can simplify inventory and layout because there is no left-right distinction during installation.

Side Mount Drawer Slide Fit And Installation Focus

This 12 inch side mount ball bearing drawer slide from Knape and Vogt uses a defined side clearance of 1/2 inch plus 1/32 inch, minus 0 each side, so cabinet designers can work from a precise formula when sizing drawer box widths. The height of 1-13/16 inch sets a known vertical envelope, supporting layout where multiple drawers stack inside a case and where face frame or frameless constructions demand tight planning. The 32 mm pattern fits work centered around system 32 drilling, supporting production lines that rely on consistent hole spacing for speed. Recommended fasteners of #7 x 1/2 inch Phillips pan head screws match the mounting holes, giving installers a clear choice when fastening slides to both the cabinet and drawer members.

Using KV 8405B 12 Slides In Cabinet Projects

Where These 12 Inch Over Travel Slides Fit Best

The Knape and Vogt KV 8405B 12 drawer slides use a side mount configuration, so they suit cabinets built to accept slides on the outer sides of the drawer box. The 12 inch nominal length targets shallow to medium-depth drawers, such as utility drawers, small cabinet bays, or shop storage pieces built around that depth. With 1 inch over-travel, these slides allow the drawer front to move past their nominal length, pulling the rear of the drawer beyond the cabinet front line, which can be useful when drawers store smaller parts or tools that tend to sit at the very back. The 32 mm pattern helps these slides integrate into frameless cabinets or any construction that follows system 32 drilling, keeping hole layouts consistent.

Details That Support Repeatable Drawer Performance

The ball bearing design of the KV 8405 Series slides provides guided movement along the raceways, which matters for drawers that will be opened and closed frequently in shop, office, or residential environments. A ball retainer latch inside the slide helps keep the bearings in the correct track, contributing to consistent movement as the slide cycles. Lever disconnect gives technicians a way to separate drawer and cabinet members without tools at the lever, which aids in assembly, finishing, or later adjustments when a drawer must be removed for access. Polymer stop cushions contact when the slide reaches its travel limit, tempering the stop, which can help the drawer feel more controlled when it meets the end of travel. The non-handed configuration further supports repeatable installation because either slide can mount on either side, reducing orientation errors and simplifying training for installers. The anochrome finish coats the slide members in a uniform metallic surface, giving a consistent appearance that suits many cabinet interiors.

Common Questions About KV 8405B 12 Drawer Slides

Choose The Right 12 Inch KV 8405B Slide

The Knape and Vogt 12 inch over travel drawer slides with ball bearings, 1 inch over-travel, and side clearance of 1/2 inch plus 1/32 inch, minus 0 each side give cabinet builders defined dimensions to design around. With lever disconnect, polymer stop cushions, non-handed layout, and 32 mm pattern support, these KV 8405B 12 slides fit workflows that value straightforward mounting and consistent drawer performance. Select this slide when a 12 inch side mount ball bearing member with over-travel and anochrome finish matches the cabinet depth and drilling system.