Knape And Vogt 24 Inch Drawer Slides For Smooth Travel

Knape and Vogt 24 inch drawer slides define this 8405 Series side mount drawer slide with a 24 inch length that suits standard cabinet drawer depths, giving installers a predictable fit when laying out carcasses and drawer boxes. The 1 inch over-travel lets the drawer extend past the cabinet face, improving access to contents at the back of the drawer in tight shop or jobsite layouts. A ball bearing design supports smooth motion along the full stroke, which helps drawers open and close with consistent feel even under regular use. The slides are part of the Knape and Vogt 8405 Series, tying into a familiar product family that many shops keep in their standard hardware lists. An anochrome finish provides a uniform, neutral appearance at the slide, which helps match common cabinet interiors without drawing attention to the hardware.

Key 8405B 24 Details For Daily Cabinet Work

• The 1 inch over-travel allows the drawer to move beyond the cabinet front, which improves reach to items at the rear of the drawer and reduces awkward bending when working at base cabinets.
• A side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side sets a clear machining target, so case openings and drawers can be sized accurately without trial-and-error fitting.
• The 1-13/16 inch height defines the slide envelope, helping you plan drawer side heights and hardware stacking when multiple drawers share a cabinet bay in vertical banks.
• The 32 mm pattern is marked as present, aligning the slide with system drilling patterns used in modern cabinet construction to streamline line boring and jig-based installation.
• A lever disconnect feature lets the drawer member release from the cabinet member, simplifying drawer removal for finishing, transport, or future adjustment without disturbing the cabinet installation.
• The ball retainer latch and polymer stop cushions work together to support controlled movement at the ends of travel, which can help damp impact and maintain a consistent feel at closure.

Side Mount Installation And Fastener Alignment

This 8405B 24 model is a side mount drawer slide, so both members register against the cabinet and drawer sides, which aligns well with face frame and frameless cabinet layouts using straight side panels. Recommended fasteners are #7 x 1/2 inch Phillips pan head screws, giving a defined shank and head size that fits the hardware holes and seats properly during drive. The specified side clearance of 1/2 inch plus 1/32 inch minus 0 inch per side provides a tight but achievable tolerance band, which supports smoother sliding action once installed. The 32 mm pattern reference means the slide hole layout follows a familiar system pattern, which helps coordinate with line-bored cabinets and speeds repeat installations across multiple boxes in a run.

Drawer Slide Performance In Real Cabinet Builds

Where This 8405B 24 Slide Fits Best

The Knape and Vogt 8405B 24 side mount drawer slide, at 24 inch length, suits full-depth drawers in kitchen, bath, and shop cabinets where standard carcass depths are used. Its 1 inch over-travel allows drawers to clear the cabinet face, which is especially useful in base cabinets with deep storage where access to the back is critical. The unhanded design means either slide can be used on either side, streamlining bench setup and inventory because no left or right distinction is needed. With a height of 1-13/16 inch, the slide fits many drawer side profiles, supporting both taller utility drawers and medium-depth storage without conflicting with typical under-shelf clearances. The 32 mm pattern alignment lets it drop into cabinets built on system holes, tying into production drilling processes found in many professional shops.

Details That Support Repeatable, Low-Rework Installs

The specified side clearance of 1/2 inch plus 1/32 inch minus 0 inch per side gives a defined tolerance window, which reduces guesswork when sizing drawer boxes and helps limit callbacks due to binding or excessive play. The lever disconnect feature lets the installer separate drawer and cabinet members quickly, making it easier to finish drawer boxes, adjust reveals, or work on interiors without supporting the full assembly. A ball bearing construction contributes to smooth travel, helping drawers glide reliably once the clearances are set within the specified range. The ball retainer latch and polymer stop cushions manage the slide at the ends of travel, which can reduce harsh impacts and help the slide components stay aligned over repeated use. As an anochrome finished slide from the 8405 Series, it integrates with other Knape and Vogt hardware selections, supporting consistent hardware choices across larger projects where matching components and predictable performance matter.

Common Questions About KV 8405B 24 Slides

Selecting This Slide For Your Next Cabinet Run

The Knape and Vogt 24 inch drawer slides 8405B 24 combine 1 inch over-travel, defined side clearance, and side mount installation, giving cabinet shops a predictable, repeatable hardware choice. Pair the 32 mm pattern reference, anochrome finish, and specified #7 x 1/2 inch Phillips pan head screws to align with existing drilling setups and fastening habits. For projects built around the Knape and Vogt 8405 Series, this 24 inch model offers a straightforward way to match slide length to standard cabinet depths while keeping motion and fit consistent across the job.