Omega National Maple Plate Rack 3/4"W x 13-1/16"H x 36"L - NPD-36-RTAMA

NOTE: As of 4/13/26, Omega National's prefix has changed from NP to RS. This part number has changed from NPDR36RTA-M to RSDR36RTA-M.

Omega National Maple Plate Rack For Cabinet Displays

Omega National maple plate rack gives you a solid wood way to organize and display plates in kitchen or bath cabinetry using matching maple components. This plate display rack is a ready-to-assemble (RTA) kit designed to build a front and back pair of racks that align in a cabinet opening. The assembled unit stands 13-1/16 inches high and 36 inches long, so it fits runs where a three-foot rack length is needed. Each finished rack uses 3/8 inch diameter dowels set 2 inches on center, creating evenly spaced channels that hold plates upright. The kit uses 36 inch long top and bottom pre-drilled rails in maple, so dowel spacing is factory-set and consistent across the length. Solid unfinished wood lets you sand and finish the maple to coordinate with surrounding cabinet interiors or doors.

Key Maple Plate Rack Details That Support Jobs

• This plate rack RTA kit from Omega National Products builds one front and one back rack pair, so plates are supported at both the front and rear of a cabinet run for stable vertical storage.
• The assembled maple plate rack height of 13-1/16 inches gives a defined vertical space for plate display, helping you match the rack to face frame openings or full-access cabinet interiors during layout.
• The 36 inch assembled rack length provides a continuous run for plate storage, which can simplify planning in standard three-foot cabinet sections or under-cabinet plate displays.
• Top and bottom rails are pre-drilled along the 36 inch length, so dowel locations are fixed at the factory and dowels seat correctly without layout work, supporting faster, repeatable assembly.
• Dowels are 3/8 inch diameter and positioned 2 inches on center, producing uniform slots that hold a series of plates in consistent spacing, useful for both display appearance and everyday access.
• The kit uses solid unfinished wood in the maple species, so the installer can stain, clear-coat, or paint to coordinate with custom cabinetry or existing maple casework.

Installation Geometry And Assembly-Oriented Design

This ready-to-assemble maple plate rack uses 36 inch long, pre-drilled top and bottom rails paired with 12 inch long dowels, so assembly becomes a matter of seating each dowel into accurately spaced holes rather than laying out centers. With dowels at 3/8 inch diameter and 2 inches on center, the geometry creates predictable plate channels along the full 36 inch run, which simplifies aligning the rack within a cabinet bay. The finished height of 13-1/16 inches provides a known dimension when planning vertical clearances above shelves or within framed openings. Because the kit forms both front and back racks from matching components, the installer can maintain parallel alignment, giving plates two points of support along their edges.

Using The NPD-36-RTAMA Maple Plate Display Rack

Where This 36 Inch Plate Rack Fits Best

This Omega National maple plate rack is a plate display rack intended for kitchen and bath cabinet installations where a 36 inch wide run is available for vertical plate storage. The assembled rack height of 13-1/16 inches suits cabinet interiors that can accept a little over 13 inches of vertical space above a shelf or within a compartment. Because the RTA kit builds both a front and a back rack from matching maple rails and dowels, it works in open-front cabinet sections where plates need support near the front of the shelf and again toward the back. The 3/8 inch diameter dowels extend 12 inches between top and bottom rails, giving a substantial depth for typical dinner plates or serving pieces to rest between racks. Solid unfinished maple construction pairs naturally with maple cabinetry where a coordinated interior is desired, and the plate rack category placement reflects its role as a cabinet plate display solution.

Why The Rail And Dowel Layout Supports Consistent Results

The NPD-36-RTAMA plate rack RTA kit ships as 36 inch long pre-drilled top and bottom rails and 12 inch long dowels intended to construct a front and back rack pair, so every dowel location is predetermined and mirrored from front to back for consistent spacing. With dowels sized at 3/8 inch diameter and located 2 inches on center, the rack establishes a repeating pattern of channels that hold a series of plates at regular intervals, which helps maintain an even visual rhythm across the cabinet opening. The 13-1/16 inch assembled height sets the rails at a constant separation, so all dowels match length and seating depth, streamlining any cutting or finishing workflow. Since the plate rack is made from solid unfinished wood in the maple species, the surface is ready for the finisher to sand and apply coatings as part of the same finishing schedule used for matching cabinet doors, frames, or interiors.

Common Questions About This Maple Plate Display Rack

Select The Right Maple Plate Rack For Your Run

The Omega National maple plate rack RTA kit with 13-1/16 inch height and 36 inch length suits projects calling for a solid wood plate display rack across a three-foot cabinet span. With 3/8 inch dowels spaced 2 inches on center and rails pre-drilled for those dowels, the system delivers consistent plate channels without field layout. Selecting the NPD-36-RTAMA model gives you a solid unfinished maple solution that can be finished to match surrounding cabinetry while providing a defined geometry for vertical plate storage.