
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
nickel-plated euro tray hinge defines this Knape and Vogt sink tip out tray hinge and sets up how it works on a cabinet false front. This hinge is a sink tip out tray hinge, so it is designed to pivot a narrow tray behind a false drawer front for small-item storage at a sink. The hinge is nickel-plated, which provides a smooth metal surface that moves cleanly at the pivot points and maintains a consistent appearance with other nickel hardware in the same run of cabinetry. The design is a Euro tray hinge style with an end cap, so it offers a compact profile that tucks into the narrow space behind the panel and keeps the moving parts protected at the ends for repeatable motion. The hinge can be used on other traditional or system 32 cabinetry, which gives flexibility to use the same part across different cabinet construction methods on a job.
This hinge can be used on other traditional or system 32 cabinetry, so it suits both face-frame and 32 mm line drill patterns where a sink tip out tray is required. The adjusting screw for control of opening range from 40 degrees to 90 degrees lets the installer tailor the swing to the depth of the tray and to nearby obstructions, providing a way to fine-tune the final stop position after the hinge is mounted. The lower overhang must not exceed 3/4 inch for full opening clearance, which ties the cabinet geometry directly to hinge performance and helps determine whether the tray will reach the full 90-degree position or stop earlier against the structure.
This hinge falls in the sink tip out tray hinges class, so it is intended for installations where a false front at a sink is converted into a tip out tray. The hinge can be used on other traditional or system 32 cabinetry, which means it suits common cabinet construction schemes in kitchens, baths, or similar casework that follow either framed layouts or 32 mm system layouts. By using a nickel-plated euro tray hinge with end cap on these cabinets, the installer gains a compact pivot that operates in the tight vertical space directly behind a narrow false front panel. The classification as a specialty hinge under Hinges|Specialty Hinges indicates it addresses this specific motion requirement rather than general door swinging, so it focuses its geometry and travel on the short arc needed to tilt a tray.
The adjusting screw for control of opening range from 40 degrees to 90 degrees gives a built-in method to set the angle that the tray reaches, so the motion can be tuned to keep the tray within a comfortable reach zone while staying clear of nearby fixtures. This hinge specifies that the lower overhang must not exceed 3/4 inch for full opening clearance, which directly links the cabinet design to the achievable opening angle and helps the installer predict whether the hinge will deliver the full 90-degree swing. The nickel-plated finish on this Knape and Vogt ET-H-N hinge provides a consistent metal surface at the moving joints, supporting smooth action each time the tray is opened and closed. Being identified as a sink tip out tray hinge in the Hinges|Specialty Hinges category, it focuses on the short, controlled tilt motion needed for a false front, which helps maintain alignment of the front with surrounding doors when the tray is closed.
This hinge is a sink tip out tray hinge, so it is designed for false fronts that tilt out to reveal a narrow tray, typically at a sink or similar cabinet location.
This hinge can be used on other traditional or system 32 cabinetry, so it fits cabinets laid out on the 32 mm drilling system as well as more conventional framed designs.
The hinge has an adjusting screw for control of opening range from 40 degrees to 90 degrees, so the installer can set the final tray angle to match space and access requirements.
The hinge states that the lower overhang must not exceed 3/4 inch for full opening clearance, so keeping overhang within this dimension allows the tray to reach its full swing.
This hinge is described as FALSE FRNT TRAY HNGE,NICKEL with manufacturer part number ET-H-N, so it can be matched consistently to specifications and reorders.
The hinge is nickel-plated, so its metal surfaces present a smooth, uniform finish that works well with other nickel hardware and supports consistent movement at the pivots.
This Knape and Vogt 3-3/4 inch nickel-plated euro tray hinge with end cap is defined as a sink tip out tray hinge, so it targets the motion needed behind a false front at a sink. With an adjusting screw for control of opening range from 40 degrees to 90 degrees and a defined lower overhang limit of 3/4 inch for full opening clearance, it ties the hinge setup directly to cabinet geometry and working space. For projects using traditional or system 32 cabinetry where a nickel finish is preferred, this ET-H-N hinge offers a clearly specified option that can be matched to drawings, schedules, and repeat jobs.
Sold In: 1 Pair