
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
This Würth #8 x 3/4-inch truss head screw is built for mounting European cup hinges, drawer slides, and other cabinet hardware to panel and face-frame surfaces. The 3/4-inch length is sized to seat hardware mounting plates firmly without over-penetrating typical 3/4-inch cabinet panels.
At 3/4 inch, this screw is the go-to length when hardware mounting plates sit against a standard 3/4-inch cabinet panel or face frame. It engages enough material to hold the hardware plate firmly under daily load cycling, while stopping well short of punching through the panel face. Cabinet shops installing runs of European cup hinges or undermount and side-mount drawer slides will find this length covers the bulk of their hardware-mounting work without swapping to a longer screw for each application.
The wide, low-profile truss head bears evenly across the hardware mounting hole, which matters when the hole in the plate is slightly oversized relative to the screw gauge. The Type 17 Auger point handles the entry: the fluted tip clears wood fiber as it advances, so the screw starts cleanly even in dense plywood or particleboard without wandering off the bore. Coarse thread pulls the plate tight and holds it against repeated opening and closing cycles.
Cabinet shops running production lines will get the most out of the 1,000-count box, keeping a full supply at the bench without mid-run restocking. Installers working on kitchen or bath cabinet retrofits will appreciate having a purpose-built hardware-mounting screw rather than improvising with a general-purpose wood screw that may seat unevenly under the plate. The #2 Phillips drive means no special bits are required on the jobsite. Interior use only; the zinc finish is sized for dry, climate-controlled cabinet environments.
The truss head has a wider, flatter bearing surface than a standard pan head, so it spans mounting-plate holes more effectively and distributes clamping force over a larger area. This reduces the chance of the head pulling slightly into an oversized hole and leaving the hardware loose.
Yes. Most European hinge mounting plates and drawer slide brackets are designed for installation into 3/4-inch material, which is the standard panel thickness for both face-frame and frameless (32mm system) cabinetry. The 3/4-inch length engages the panel fully without over-penetrating.
Not in most cases for panel materials like plywood and particleboard. The Type 17 Auger point's fluted tip cuts its own path and clears chips as it advances, so a separate pilot hole is typically not needed. In very dense hardwood panels or near a board edge, a pilot hole will help prevent splitting.
No. The zinc finish provides standard corrosion protection for dry, indoor conditions. For cabinet installations in areas with high moisture exposure, such as near sinks in unconditioned spaces, a screw with a higher-grade finish would be the better choice.
Each box contains 1,000 screws, a practical quantity for cabinet shops and installers running through hardware mounting on multi-cabinet projects.
A screw that fits the hardware plate, the panel thickness, and the drive bit already in your tool keeps the installation moving without adjustments or substitutions — and that is exactly what this 3/4-inch truss head screw is designed to do.
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1000 Each | WW58120 Mfr# 3670000250961 1000 | Würth #8 x 5/8" Truss Head Hinge and Drawer Slide Installation Screw Phillips Drive - Type 17 Auger Point Coarse Thread Zinc, 3670000250961 1000 - 1000/Box | ||||
Sold in: 10 Each | WW614176461 Mfr# 0614176461005 10 | #2 x 1" Phillips Drive Insert Bit (10/Bag) | ||||
Sold in: 10000 Each | WW58130 Mfr# 367000025096110000 | Würth #8 x 5/8" Truss Head Hinge and Drawer Slide Installation Screw Phillips Drive - Type 17 Auger Point Coarse Thread Zinc, 367000025096110000 - 10000/Box | ||||
Sold in: 10000 Each | WW58150 Mfr# 367000024996110000 | Würth #8 x 3/4" Truss Head Hinge and Drawer Slide Installation Screw Phillips Drive - Type 17 Auger Point Coarse Thread Zinc, 367000024996110000 - 10000/Box |
Sold In: 1000 Each