Wurth #8 x 3/4 Truss Head Screw For Hardware
Wurth #8 x 3/4 truss head screw is a cabinet fastener designed for mounting hinges and drawer slides. The screw uses a large truss head, so the head resists sinking into soft woods during installation, which helps maintain consistent clamping pressure on the hinge or slide flange. Its coarse thread pattern is suited to wood fastening, giving strong bite in typical cabinet materials. The screw is manufactured with a Type 17 auger point, which is designed to prevent splitting in hardwoods when hardware is attached into or near the edge of the material, protecting door and cabinet parts during hardware layout. A #2 Phillips drive recess matches standard Phillips drive bits, which supports straightforward driving with common tools in the shop or on site. The screw has a zinc finish, so it presents a typical cabinet fastener appearance that matches other zinc fastener heads in many installations.
Key Screw Details That Support Hardware Mounting
- The large truss head reduces sinking into soft woods, which keeps hinge and drawer slide flanges seated on the surface instead of pulling down into the material during tightening, helping maintain alignment.
- The Type 17 auger point is designed to prevent splitting in hardwoods when hardware is attached into or near the edge, which helps protect stile and edge stock during hinge and slide placement.
- The coarse thread pattern matches wood fastening needs, so the screw develops holding power in typical cabinet materials and supports hardware staying tight under regular door and drawer use.
- The #2 Phillips drive works with standard Phillips drive bits, so installers can drive these screws with commonly used drivers without changing over to specialty drive systems during a run of cabinets.
- The zinc finish provides a conventional cabinet screw appearance, so exposed heads around certain hinges or slides visually match other zinc fasteners in the assembly.
Installation Behavior Of This Hinge And Slide Screw
This Wurth screw combines a Type 17 auger point and coarse threads, so it starts and pulls into wood while the point design is intended to reduce splitting in hardwoods at or near edges. That behavior matters when driving into door edges or cabinet face frames where edge distance is tight. The large truss head spreads load across more surface around the hinge or drawer slide holes, so the head helps resist pull-through in softer stock. Using a #2 Phillips drive, the screw engages common bits used on drills or drivers, which supports consistent torque application across a job. The 3/4 inch length and #8 diameter form a compact hardware mounting fastener, so it suits applications where hinge or slide mounting holes are sized for #8 screws.
Using This Screw For Cabinet Hardware Work
Where This Truss Head Screw Is Typically Applied
The Wurth #8 x 3/4 truss head hinge and drawer slide installation screw is described for use with hinges and drawer slides, so it serves as the primary mounting fastener for those hardware components in cabinet and furniture projects. Its large truss head reduces sinking into soft woods, which is useful on cabinet sides, stretchers, or face frames made from softwood or soft composite materials where head pull-down can distort hardware. The Type 17 auger point is designed to prevent splitting when fastening into or near hardwood edges, so it is suited to attaching hinges along door edges or fastening slides close to solid-wood edges in high-end cabinetry. With its coarse thread pattern, the screw is oriented toward wood-based substrates, so it functions in particleboard, plywood, or solid wood where cabinet hinges and slides are usually fastened. The zinc finish gives it a typical cabinet fastener look, which aligns with common hardware finishes in many shops.
How Screw Design Details Support Consistent Results
The combination of large truss head and coarse threads helps hold hinges and drawer slides firmly without the head drawing deeply into softer material, so the hardware seats flat and stays aligned with the original layout lines. Because the Type 17 auger point is designed to prevent splitting in hardwoods when driving at or near edges, it supports repeated hinge and slide installation along door and cabinet edges without damaging stock, which is important when running multiple doors and cases. Using a #2 Phillips drive, the screw interfaces with standard bits commonly stocked in woodworking environments, so installers can maintain consistent driver control from one screw to the next. The defined #8 diameter gives a familiar fit through hinge and slide mounting holes labeled for that screw size, so hole clearance and bearing surfaces behave as expected. Together, these details support repeatable fastening performance across cabinet runs that use the same hinge and drawer slide lines.
Common Questions About This Wurth Installation Screw
What is this Wurth screw designed to fasten?
The screw is described as a hinge and drawer slide installation screw, so it is intended to fasten hinges and drawer slides to cabinet or furniture materials.
How does the large truss head affect hinge or slide mounting?
The large truss head reduces sinking in soft woods, so hinge and slide flanges stay seated on the surface and maintain alignment under tightening.
Why is the Type 17 auger point important for hardwood edges?
The Type 17 auger point is designed to prevent splitting in hardwoods when attaching hardware into or near the edge, protecting door and frame stock.
What drive style is used with this cabinet screw?
The screw uses a #2 Phillips drive, so it works with standard #2 Phillips drive bits commonly used in drills and drivers.
How does the coarse thread help in cabinet materials?
The coarse thread is suited to wood fastening, so it provides bite and holding strength in typical cabinet woods, plywood, and composites.
What visual finish does this installation screw provide?
The screw has a zinc finish, so visible heads show a standard zinc appearance that matches many cabinet fasteners and hardware components.
Selecting This Screw For Hinge And Slide Runs
The Wurth #8 x 3/4 truss head hinge and drawer slide installation screw combines a large truss head, coarse threads, and a Type 17 auger point, so it supports mounting cabinet hinges and drawer slides in both soft woods and hardwood edges. With a #2 Phillips drive and zinc finish, it aligns with common cabinet shop tools and fastener appearance. When a project calls for a #8 x 3/4 inch screw dedicated to hinge and drawer slide installation, this configuration offers a focused option for those fastening points.
