Hinge And Drawer Slide Installation Screw For Hardware
Hinge and drawer slide installation screw from Wurth is a #8 x 5/8 inch screw designed specifically for mounting hinge and drawer slide hardware, so installers can fasten hardware with a consistent size across a project. The large truss head is described as reducing sinking of the head in soft woods, which helps spread the load over more surface area and keeps the head from pulling too deeply into softer cabinet materials. This screw uses coarse thread, which is suited for biting into wood when hardware is attached to the cabinet or drawer components. The screw uses a #2 Phillips Drive, so it works with common #2 Phillips drive bits already used on many job sites and in shops. The screw is zinc, matching the zinc description in the product data to support typical indoor cabinet environments.
Key Screw Details For Hardware Installers
- The large truss head is described as reducing sinking of the head in soft woods, which helps the screw seat firmly on hinge or drawer slide holes while limiting head pull-through in softer cabinet substrates.
- The Type 17 Auger point is described as designed to prevent splitting in hardwoods when hardware is attached into or near the edge of material, which supports neater edges when driving close to door or face-frame edges.
- The coarse thread works with wood substrates when attaching hardware, giving the screw grip for holding hinges and drawer slides against cabinet parts under normal use.
- The #2 Phillips Drive matches the stated drive type, so installers can use standard #2 Phillips bits to run these fasteners without changing drivers during hinge and slide installation.
- The screw is zinc per the description, which gives a zinc surface consistent with many interior cabinet fasteners used around hinges, drawer slides, and similar hardware.
Installation Behavior And Drive Interaction
This Wurth #8 x 5/8 inch truss head screw uses a Type 17 Auger point that is described as designed to prevent splitting in hardwoods when hardware is attached into or near the edge of material, which supports driving near hardwood edges where hinges or drawer slides often mount. The coarse thread engages wood as the screw advances, which helps hold cabinet hardware firmly once seated. The #2 Phillips Drive works with #2 Phillips Drive bits noted in the product description, so installers can run these screws with widely available Phillips drivers for consistent torque and alignment while fastening hinge and drawer slide hardware.
Using This Screw In Cabinet Hardware Work
Where This Truss Head Screw Is Typically Applied
The web description states this screw is for hinge and drawer slide installation, which ties it directly to installing hinge and drawer slide hardware on cabinet doors and drawers. The large truss head is described as reducing sinking of the head in soft woods, which supports use in softer cabinet materials where head pull-through is a concern at hinge leaf or slide mounting holes. The Type 17 Auger point is described as designed to prevent splitting in hardwoods when hardware is attached into or near the edge of material, making the screw suitable for mounting hardware into hardwood cabinet frames, drawer sides, or door rails close to the edge. The #8 x 5/8 inch size works as a short fastener length for holding hardware faces without extending deeply into thin cabinet parts.
Why These Screw Details Support Cleaner Results
The large truss head described in the product data reduces sinking of the head in soft woods, so hinge and drawer slide flanges stay supported against the surface instead of denting or crushing softer stock under the head. The Type 17 Auger point is designed to prevent splitting in hardwoods when hardware is attached into or near the edge of material, which reduces edge damage as screws are driven into hardwood rails and stiles where many hinges mount. The coarse thread profile works with wood when hardware is attached, giving consistent pull-down on hinge leaves and drawer slide brackets under typical cabinet loads. The #2 Phillips Drive matches standard #2 Phillips Drive bits, which supports repeatable driving and reduces cam-out when installers are running multiple screws for each hinge or drawer slide during cabinet assembly or installation.
Common Questions About This Wurth Screw
What is the size of this hinge and drawer slide installation screw?
The screw is described as a Wurth #8 x 5/8 inch truss head screw, so it uses a #8 shank diameter with a 5/8 inch length suited to hardware mounting.
How does the large truss head help in soft woods?
The large truss head is stated to reduce sinking of the head in soft woods, which helps keep the head sitting on the hardware flange instead of pulling into the softer material.
Why is a Type 17 Auger point useful near hardwood edges?
The Type 17 Auger point is described as designed to prevent splitting in hardwoods when hardware is attached into or near the edge, which supports cleaner edges around hinge or slide locations.
What drive style does this Wurth screw use?
The screw uses #2 Phillips Drive, so it works with #2 Phillips Drive bits mentioned in the description for running hinge and drawer slide fasteners.
Is this screw intended for hinge and drawer slide installation?
The product name identifies it as a hinge and drawer slide installation screw, tying its size, head style, and point design to those cabinet hardware applications.
What material description is provided for this screw?
The SAP description identifies the screw as zinc, and the web description notes zinc, indicating a zinc screw consistent with many interior cabinet fasteners.
Selecting This Screw For Hardware Mounting
This Wurth #8 x 5/8 inch truss head hinge and drawer slide installation screw combines a large truss head, coarse thread, and Type 17 Auger point described for use in soft woods and hardwoods near edges, so it matches common cabinet door and drawer hardware mounting needs. The #2 Phillips Drive works with #2 Phillips Drive bits already described, supporting straightforward driving of multiple screws per hinge or drawer slide. For projects using cabinet hinges and drawer slides in wood substrates, this screw aligns its length, head style, and point design with typical hardware installation tasks.
