#8 x 1-1/2 flat head assembly screw is a case hardened, lubricated screw designed for wood working applications, so it supports repeatable fastening in cabinet and furniture builds. The patented serrated tooth turbo thread allows for quick starting, which helps the screw bite rapidly into wood during assembly. That same turbo thread reduces splitting, so edge and end-grain locations are protected in typical cabinet parts. Reduced drive torque from the lubricated turbo thread means the driver works under less load, helpful during long production runs. This screw uses a flat head, so it seats flush in countersunk holes on face frames, slides, hinges and hardware. The sharp point combines with the thread design to engage wood without pre-threading, which speeds up assembly steps.
This flat head assembly screw uses #2 Square Drive bits to insert, so the driver interface is matched for consistent bit engagement. That #2 square drive helps transfer torque directly, which supports clean seating of the screw without excessive cam-out. #2 Phillips Drive bits can be used for after market adjustment, so existing Phillips drivers can turn the screw when alignment changes are needed later in the job. The combination of square drive for primary installation and Phillips for later adjustment lets installers use common shop drivers while still getting the benefits of a square drive during initial assembly.
This Wurth #8 x 1-1/2 inch flat head assembly screw is specified for all wood working applications, so it fits cabinet, casework, and general furniture assembly tasks. The web description identifies use in assembly, face frame, slides, hinges and hardware, which ties the screw directly to common shop hardware mounting steps. The sharp point supports starting directly into wood components, so installers can position screws accurately on rails, stiles and brackets. The screw size and thread configuration are suited to typical wood thicknesses found in cabinet parts, so it fits routine construction details. Because the turbo thread is threaded from the bottom portion upward on this length, the screw body is arranged to pull joints together from inside the material.
The patented serrated tooth turbo thread allows for quick starting and less drive torque, so each screw drives smoothly and helps reduce effort per fastener. The lubricated design further lowers friction during driving, which supports stable torque output from powered drivers. Reduced splitting from the turbo thread matters when working near corners and edges, because it helps maintain the integrity of narrow face frame members. Case hardened construction strengthens the screw core, so it holds up under the torque levels used in assembly, face frame, slides, hinges and hardware installations. The ability to use #2 Square Drive bits for main installation gives a solid engagement at the head, while #2 Phillips Drive bits can be used for after market adjustment so minor position changes remain straightforward after initial install.
This Wurth #8 x 1-1/2 inch flat head assembly screw is intended for all wood working applications, including assembly, face frame, slides, hinges and hardware, so it matches common cabinet and furniture fastening tasks.
The patented serrated tooth turbo thread allows for quick starting, reduced splitting, and less drive torque, so screws drive smoothly while helping protect wood components from damage during installation.
This flat head assembly screw uses #2 Square Drive bits to insert, and #2 Phillips Drive bits can be used for after market adjustment, so common shop drivers interface with the screw head.
The screw is case hardened, which strengthens the screw body and supports firm clamping of joints in wood working applications where repeated driving torque is applied.
For this line, 3/4 inch and 1 inch lengths are threaded fully, and all other sizes are threaded two-thirds from the bottom, so this 1-1/2 inch screw has its thread on the lower portion.
The screw is lubricated, which reduces friction while driving and contributes to less drive torque, so driver tools work efficiently during repeated installation cycles.
This Wurth #8 x 1-1/2 inch flat head assembly screw with patented serrated tooth turbo thread, sharp point and lubrication is set up for wood working applications such as assembly, face frame, slides, hinges and hardware, so it aligns with everyday shop tasks. The case hardened, combo-drive design supports stable installation and later after market adjustment using #2 Square Drive bits and #2 Phillips Drive bits. Selecting this screw brings a threaded two-thirds-from-bottom layout on this length, plus reduced splitting and lower drive torque from the turbo thread, so joints pull together cleanly in typical wood components.
Sold In: 5000 Each
