#8 x 2 flat head assembly screw is designed as a case hardened, lubricated fastener for wood working applications where consistent driving and firm hold are needed across assemblies. The patented serrated tooth turbo thread starts quickly in wood, so installers can begin driving with less walking and reduced start time on repetitive cabinet work. This same turbo thread design reduces splitting, which supports cleaner results in face frames, slides, hinges, and hardware installations. The lubricated finish lowers drive torque, allowing powered drivers to run cooler and batteries to last longer during long runs of fasteners. A flat head profile seats flush in countersunk holes, helping parts close up tightly in assemblies. The sharp point engages wood fibers immediately, which supports faster penetration in typical shop materials without predrilling in many standard situations.
This Wurth assembly screw uses a #2 Square Drive bit to insert, giving a positive, low-cam-out connection between bit and screw head during primary installation. The same head also accepts #2 Phillips Drive bits for after market adjustment, so installers can return to a project later with common bits and reset depth or alignment. Length options of 3/4 inch and 1 inch are threaded fully, helping shorter fasteners grip along their entire length in thin stock. All other sizes are threaded two-thirds from the bottom of the screw, which focuses holding power toward the tip area while leaving a partial smooth section nearer the head for drawing materials together. The sharp point interacts with these thread patterns to advance quickly into wood and support predictable pull-down.
This Wurth #8 x 2 inch flat head assembly screw is intended for use in wood working applications such as assembly, face frame, slides, hinges, and hardware. In cabinet assembly, the flat head seats into countersunk holes, allowing panels and rails to sit flush for tight joints. When used in face frames, the sharp point and turbo thread grip narrow stock efficiently, helping rails and stiles draw together without excessive splitting. For slides and hinges, the screw length and wood-focused thread provide a secure connection between hardware components and cabinet members. The lubricated body supports smooth driving into typical shop materials, which helps maintain alignment of hardware during installation by limiting driver chatter and sudden stops.
The patented serrated tooth turbo thread allows for quick starting, so each screw begins cutting into wood with minimal pressure, improving productivity on large batch runs. Reduced splitting from this thread form means edges on face frames and small parts stay more intact, which reduces the likelihood of damaged pieces during installation. Less drive torque, supported by the lubricated finish, allows cordless tools to run longer between charges and helps maintain consistent recess depth of the flat head. Using #2 Square Drive bits to insert gives installers a stable driving connection, which is important when working at arm's length inside cabinets or along tall casework. The option to use #2 Phillips Drive bits for after market adjustment adds flexibility when realigning hardware, as the same screw can be backed out or reset using commonly carried bits. Threading that varies by length - fully threaded on 3/4 inch and 1 inch, two-thirds from the bottom on longer sizes - tailors the grip pattern to different stock thicknesses, supporting effective clamping while the flat head draws parts tightly together.
The screw is described for use in all wood working applications, including assembly, face frame, slides, hinges, and hardware, so it serves as a general-purpose fastener across typical cabinet and furniture work.
The patented serrated tooth turbo thread allows quick starting, reduced splitting, and less drive torque, which speeds installations and supports cleaner results in common woodworking materials.
The screw is lubricated to reduce drive torque, which helps tools work with less strain and supports consistent seating of the flat head during repetitive installation.
The screw is case hardened, giving the shank and head drive area added wear resistance, which supports repeated driving into wood during assembly tasks.
The screw uses #2 Square Drive bits to insert for primary installation, and #2 Phillips Drive bits can be used for after market adjustment when resetting or tuning hardware.
On 3/4 inch and 1 inch screws, the shank is threaded fully, while all other sizes are threaded two-thirds from the bottom, tailoring grip to various stock thicknesses.
This Wurth #8 x 2 inch flat head assembly screw with patented serrated tooth turbo thread offers quick starting and reduced splitting for wood working applications such as assembly, face frame, slides, hinges, and hardware. The lubricated, case hardened design supports lower drive torque and durable performance with #2 Square Drive bits during installation. Compatibility with #2 Phillips Drive bits for after market adjustment adds flexibility when revisiting projects. Varied thread coverage by length - fully threaded for 3/4 inch and 1 inch, two-thirds from the bottom on other sizes - adapts holding power to different stock thicknesses. Choose this configuration when a single screw style is needed to handle multiple wood-based assembly and hardware mounting tasks efficiently.
Sold In: 1000 Each
