Reeve 16-gauge steel table leg 6" h x 1-1/4" dia sat in zinc leg-6-znc-r

Reeve 16-Gauge Steel Table Leg For Low Surfaces

Reeve 16-gauge steel table leg gives you a 6 inch high, 1-1/4 inch diameter round support built for low work surfaces or tables. The leg is made of cold rolled steel, which provides a consistent, straight tube that helps keep short runs solid and stable. A satin zinc finish covers the leg, so the exposed surface has a clean metallic look that suits commercial work areas. The 16-gauge wall thickness keeps the leg robust relative to its compact size, which supports everyday use on low platforms, benches, or risers. Reeve Store Equipment Company identifies this model as LEG-6-ZNC-R, so matching additional legs or reordering for repeat projects stays straightforward when you are standardizing on a specific leg size and finish.

Key Reeve Table Leg Details For Projects

• The leg height is 6 inches, which sets work surfaces or table tops at a low profile where minimal elevation is needed for platforms or support frames.
• The round tube diameter is 1-1/4 inches, giving a compact footprint that fits under tight edges while still offering solid vertical support for the surface.
• The leg is made of cold rolled steel, providing a uniform shaft that resists bending in normal service, which helps maintain alignment on short tables and fixtures.
• Construction uses 16-gauge steel, so the wall thickness adds strength relative to the small size, which is useful where legs carry frequent loading cycles.
• The surface has a satin zinc finish, so the metal is visually consistent and suited to exposed installations where a plain steel appearance is not desired.
• The product is part of the Reeve Store Equipment Company line, which lets you coordinate this leg with other Reeve table support components specified to the same style.

Mounting Plate And Screw Hole Layout Details

Each Reeve steel table leg has a welded mounting plate, which creates a fixed interface between the tube and the work surface for a solid connection. The plate measures 3 inches by 4 inches, giving a rectangular footprint that spreads the load into the underside of the surface. Four 3/16 inch diameter screw holes are set in the plate, so you have defined points for mechanical fastening that keep the leg from rotating around the tube. Because the plate is welded to the leg, the assembly behaves as one piece, which helps keep the table corner or support position locked in place once fastened.

Using This Reeve Table Leg In Work Areas

Where The Reeve 6 Inch Table Leg Fits

This Reeve table leg at 6 inches high suits low work surfaces, short tables, or riser structures where only modest elevation is required. The 1-1/4 inch diameter keeps the leg compact, so it fits under narrow tops or along edges without taking excessive space. With its 3 inch by 4 inch welded plate, the leg interfaces cleanly with flat underside surfaces such as wood or panel substrates that accept 3/16 inch diameter screw fasteners. The satin zinc finish allows the leg to sit visibly under open work surfaces or tables without drawing attention, which suits commercial or shop environments using exposed metal supports.

Details That Support Consistent Mounting Results

The cold rolled steel construction gives the Reeve steel table leg a straight, consistent profile, which helps multiple legs line up evenly under a shared top. The 16-gauge wall thickness works with the welded 3 inch by 4 inch plate so the leg and plate act together under load, reducing flex where the tube meets the mounting surface. Four 3/16 inch diameter screw holes on the plate define a clear fastening pattern, which simplifies repeating the same layout across several legs on a job. The satin zinc finish provides a uniform metal surface that helps the legs present the same appearance from leg to leg, supporting a consistent look across multiple tables or work platforms built to the same specification.

Common Questions About Reeve Steel Table Leg Fit

Selecting This Reeve Leg For Your Next Build

The Reeve 16-gauge steel table leg combines a 6 inch height, 1-1/4 inch round tube, and welded 3 inch by 4 inch plate to support low surfaces with defined mounting points. The cold rolled steel and satin zinc finish align appearance and strength for shop, commercial, or fixture projects. When a job calls for a compact, round steel leg with four 3/16 inch diameter screw holes and a known part number, LEG-6-ZNC-R from Reeve Store Equipment Company provides a repeatable choice for building or expanding your work surfaces.