Amerock Kane Series Satin Nickel 12" (305 mm) Center to Center Appliance Pull, -BP53805G10

Amerock Kane Appliance Pull For Streamlined Projects

Amerock Kane appliance pull gives a 12 inch (305 mm) center-to-center grip that spans wider appliance or cabinet fronts, providing a substantial handhold that suits tall doors and oversized panels. The 12-15/16 inch (329 mm) overall length lines up cleanly across face panels, helping maintain consistent sightlines on banks of doors and drawer fronts. Satin Nickel finish offers a muted metallic look that works across many cabinet finishes, supporting cohesive designs in kitchens or utility spaces. Zinc die-cast construction provides a solid-feeling pull body, supporting repeated daily use on heavier fronts. A 1 inch (25 mm) width presents a broad bar profile, which helps distribute hand pressure for comfortable operation. The 1-11/16 inch (43 mm) projection stands the pull off the face enough for a confident grip, aiding users with larger hands or when operating doors from the side.

Key Kane Pull Details That Help The Job

• The 12 inch (305 mm) center-to-center drilling matches a common appliance pull layout, simplifying layout work when aligning multiple fronts and enabling straightforward replacement where that drilling already exists.
• The 12-15/16 inch (329 mm) overall length lets the pull slightly overrun the drilling span, creating balanced end margins that support symmetrical placement on wide doors or drawer heads.
• The 1-11/16 inch (43 mm) projection provides finger clearance between the hand and the door surface, which helps reduce knuckle contact on thicker fronts and makes pulling tall appliance panels smoother.
• The 1 inch (25 mm) width offers a stable gripping surface along the bar, supporting steady pulls on heavier doors where narrow pulls can feel sharp or less comfortable during frequent use.
• The 1 inch (25 mm) base diameter defines a consistent footprint at each mounting point, which helps cover typical drill holes cleanly and creates a defined bearing surface against the door or panel.
• The zinc die-cast material forms a rigid pull body, supporting firm fastening to the door and giving the handle a solid hand feel during repeated opening and closing cycles.

Installation Dimensions For Precise Kane Mounting

The 12 inch (305 mm) center-to-center dimension sets the drilling requirement for this Amerock Kane pull, guiding hole placement when laying out new doors or appliance panels. That fixed span supports straight alignment across multiple fronts, since installers can repeat the same measurement on every unit. The 1-11/16 inch (43 mm) projection defines how far the pull stands off the surface, which matters when coordinating with adjacent cabinetry or tall appliance doors that swing past nearby panels. A 1 inch (25 mm) base diameter at each end indicates the contact area at the mounting points, helping installers understand how much flat surface is needed around each hole for proper seating.

Using The Amerock Kane Pull In Real Projects

Where The Kane Satin Nickel Pull Works Best

The satin nickel finish on this Amerock Kane pull offers a neutral metallic tone that pairs with many hinge finishes and common appliance trims, supporting unified hardware selections in kitchen or utility layouts. With a 12 inch (305 mm) center-to-center span, the pull suits full-height cabinet doors or appliance fronts that benefit from a longer gripping area, aiding users when opening heavy or tall panels. The 12-15/16 inch (329 mm) overall length helps the pull visually anchor wide fronts, giving a proportion that can match tall cabinet banks or panel-ready appliances. A 1 inch (25 mm) wide bar and 1-11/16 inch (43 mm) projection provide a grip that works for varied hand sizes, which can matter in shared spaces where many users interact with the same doors. The 1 inch (25 mm) base diameter supports a defined mounting footprint, fitting well on standard stile widths while still appearing substantial on broader rails.

Dimensions That Support Consistent, Repeatable Results

The 12 inch (305 mm) center-to-center measurement on the Kane pull creates a clear drilling standard for a run of doors, helping installers reuse the same jig or template across the job. That repeatable spacing assists in keeping pulls in straight visual lines on stacked drawers and tall cabinets. The 12-15/16 inch (329 mm) overall length defines the visible bar span, aiding layout decisions such as setting consistent end clearances from door edges. With a projection of 1-11/16 inch (43 mm), the pull offers enough stand-off to clear door profiles or raised panels, which supports smooth grasping even on thicker fronts. The 1 inch (25 mm) width and 1 inch (25 mm) base diameter work together to create a balanced look at each mounting point, reducing visual strain when many pulls appear in a single field of view.

Common Questions About The Amerock Kane Appliance Pull

Choose This Pull For 12 Inch Center Layouts

The Amerock Kane satin nickel appliance pull combines a 12 inch (305 mm) center-to-center span with a 12-15/16 inch (329 mm) overall length, fitting layouts built around that drilling standard. With zinc die-cast construction, a 1 inch (25 mm) width, and 1-11/16 inch (43 mm) projection, it supports comfortable daily use on wider cabinet or appliance fronts. For projects calling for a satin nickel finish and 12 inch centers, this pull provides defined dimensions that align with measured layout and installation work.