
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Amerock Manor cup pull gives a 5-1/16 in (128 mm) center-to-center grip that spans common cabinet hole spacing, so installers can match existing drilling on many drawer fronts without layout changes. The cup pull design works as a comfortable handhold, letting fingers hook under the lip for controlled opening on wider or heavier drawers. The Manor collection identity ties this piece to other Amerock hardware from the same line, supporting visual continuity where multiple pulls are used in a room. The stated 5-1/16 in center-to-center dimension also helps plan new drawer layouts, because drill locations can be laid out from a single, consistent measurement across a bank of cabinets.
The 5-1/16 in (128 mm) center-to-center drilling dimension drives mounting layout, because holes must be bored at that spacing for the pull to seat flat. This measurement lets installers reuse 128 mm drill jigs for repetitive cabinet runs, speeding through-production work on large banks of drawers. The 5-1/2 in overall length then confirms that, once mounted, the pull will extend slightly beyond the hole pattern, which matters when positioning near door gaps or face frame edges. The 1 in projection keeps the pull from sticking too far into the room, supporting clearance when drawers pass close to adjacent doors or cabinetry.
The Amerock Manor cup pull from the Manor collection is suited to cabinet doors and drawers where a 128 mm center-to-center pattern is preferred, because the mounting holes align to that widely used spacing. Its 5-1/2 in overall length makes it a fit for medium to larger drawer fronts, giving enough visual weight across the panel without overwhelming typical cabinet rail dimensions. The 1 in width allows installation on standard drawer rails, because the pull fits comfortably within most rail heights. With a 1 in projection, the pull provides enough space for fingers to grip while remaining close to the cabinet face, which is helpful along narrow aisles where extended hardware might interfere with movement.
The 128 mm center-to-center layout on this Amerock Manor cup pull supports repeatable drilling, because installers can set up jigs to that measurement and carry it across an entire project. The fixed 5-1/2 in length paired with that drilling dimension tells installers how much overhang extends beyond the holes, which is useful when aligning pulls relative to drawer edges or decorative trim. The zinc die-cast construction keeps the pull as a single, rigid casting, so the mounting points remain stable once fastened to the drawer front. The oil-rubbed bronze finish provides a consistent surface appearance along a run of cabinets, so each installed pull presents the same dark tone and visual character. The Amerock BP26138ORB part number clearly identifies this exact combination of Manor design, zinc die-cast construction, oil-rubbed bronze finish, and 128 mm center-to-center drilling for reorder or matching on phased projects.
The Amerock Manor cup pull has a 5-1/16 in (128 mm) center-to-center size, which sets the drilling pattern for mounting across cabinet doors or drawers using that spacing.
The BP26138ORB cup pull has a 5-1/2 in overall length, so installers can plan clearances to drawer edges and neighboring hardware on the cabinet face.
The Amerock Manor cup pull is made from zinc die-cast material, giving a solid cast body that supports everyday cabinet opening and closing forces.
The oil-rubbed bronze cup pull has a 1 in projection, which defines how far it stands off the cabinet face for finger clearance and drawer movement.
The Amerock Manor BP26138ORB pull is 1 in wide, so it fits comfortably on standard drawer rails without extending into surrounding trim details.
This Amerock Manor collection pull uses an oil-rubbed bronze finish, providing a dark, coordinated appearance that matches other bronze-toned cabinet hardware.
The Amerock Manor cup pull with 5-1/16 in (128 mm) center-to-center drilling and 5-1/2 in overall length gives installers a defined pattern for cabinet runs where uniform spacing matters. The zinc die-cast construction and oil-rubbed bronze finish combine into a specific spec that can be repeated across kitchen, bath, or storage projects. When a project calls for a 128 mm center-to-center oil-rubbed bronze cup pull, this Amerock BP26138ORB model delivers those exact dimensions for consistent layout.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each | AMBP26130-26 Mfr# BP2613026 | Amerock Manor 3" (76 mm) Center to Center Polished Chrome Cup Pull, BP2613026 | ||||
Sold in: 1 Each | AMBP26138-G10 Mfr# BP26138G10 | Amerock Manor 5-1/16" (128 mm) Center to Center Satin Nickel Cup Pull, BP26138G10 | ||||
Sold in: 1 Each | AMBP26127-ORB Mfr# BP26127ORB | Amerock Manor Oil Rubbed Bronze 1-1/2" (38 mm) L x 1" (25 mm) W Knob, BP26127ORB | ||||
Sold in: 1 Each | AMBP26131-PN Mfr# BP26131PN | Amerock Manor Polished Nickel 1" (25 mm) L x 1" (25 mm) W Knob, BP26131PN |