Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson Designers Group Ten pull gives a 3-3/4 inch center to center grip that works well for standard cabinet door and drawer layouts, so drilling and alignment stay consistent from piece to piece. The pull is made from zinc die cast material, which provides a solid metal feel in hand that suits frequent cabinet use in busy spaces. Its polished nickel finish reflects surrounding surfaces, which helps the pull visually coordinate with other polished nickel decorative hardware and moldings in the same area. The overall length of 4-13/16 inches provides extra bar beyond the screw holes, which helps installers visually center the pull on wider drawer fronts. A projection of 1-3/8 inches gives clearance between the hand and the cabinet face, which supports comfortable gripping while keeping the pull profile relatively low. The 3/8 inch width keeps the pull looking streamlined while still giving a defined edge to grab.
This Berenson Designers Group Ten pull is specified with a 96 mm center to center, which matches the 3-3/4 inch hole spacing many cabinet jigs use, helping drilling stay repeatable from cabinet to cabinet. The overall length of 4-13/16 inches gives a known edge-to-hole distance, so installers can calculate reveal at door edges or drawer sides using simple measurements. With a projection of 1-3/8 inches, the pull stands off the cabinet face enough to clear typical door and drawer fronts, which supports comfortable hand access even on thicker fronts. The 3/8 inch width sets a narrow footprint on the face frame or panel, which matters when positioning pulls near edges or adjacent hardware. The specified screw size of 8-32 by 1 inch matches a common cabinet hardware thread, which coordinates with standard drilling and tapping tools used on job sites or in shops.
This Berenson Designers Group Ten pull, categorized under handles and pulls in decorative hardware and moldings, is suited for cabinet doors and drawers where a 3-3/4 inch center to center layout is preferred. The polished nickel finish allows the pull to sit well in projects that already use polished nickel decorative elements, so hardware lines can stay consistent across a kitchen, bath, or built-in run. With an overall length of 4-13/16 inches, the pull scales well on typical base and wall cabinet doors, keeping the handle visually proportional to common panel sizes. The 3/8 inch width helps the pull sit neatly on face frames and slab fronts without overpowering narrow rails. Being made from zinc die cast, the pull provides a metal option for high-touch areas, which works for active residential spaces where doors and drawers are opened frequently.
The 96 mm center to center spacing on this 4140-1014-P cabinet pull supports repeatable drilling because many cabinet templates are built around this measurement, which helps keep rows of handles straight over long cabinet runs. The defined 1-3/8 inch projection keeps each pull at the same stand-off from the fronts, which creates a uniform shadow line that installers and designers can plan around. The 4-13/16 inch total length gives a reliable outside dimension, so when laying out multiple handles, spacing between pulls can be calculated based on the bar edges rather than guessing from photos or rough estimates. The 3/8 inch width limits how much face area the pull covers, which is useful for maintaining reveal lines on narrow stile-and-rail constructions. Because the pull is zinc die cast with a polished nickel finish, the surface presents as polished metal across each piece, supporting a consistent appearance when multiple pulls are mounted side by side.
The Berenson Designers Group Ten pull has a 3-3/4 inch, or 96 mm, center to center, which coordinates with common cabinet drilling jigs and layout patterns.
The pull length is 4-13/16 inches, giving extra bar beyond the screw holes, which helps with visual centering on many doors and drawers.
The 4140-1014-P cabinet pull is zinc die cast, providing a metal body that feels solid in hand during daily cabinet use.
This polished nickel cabinet pull projects 1-3/8 inches from the cabinet surface, creating space for fingers to wrap comfortably behind the handle.
This Berenson cabinet handle uses 8-32 by 1 inch screws, aligning with a standard cabinet hardware thread for installs.
The Designers Group Ten polished nickel pull has a width of 3/8 inch, giving a slim profile on cabinet faces while still providing a defined gripping edge.
The Berenson Designers Group Ten 96 mm pull combines a 3-3/4 inch center to center layout, 4-13/16 inch overall length, and 1-3/8 inch projection, which supports consistent drilling and a comfortable grip across multiple cabinets. The zinc die cast construction with a polished nickel finish ties into polished nickel decorative hardware and moldings, so this pull can be used as part of a coordinated hardware plan. With its 3/8 inch width and defined dimensions, this pull gives installers predictable measurements to work from on each project. For a job that calls for a polished nickel, 96 mm center to center handle, this Berenson pull is ready to be specified by part number 4140-1014-P.
Sold In: 1 Each
