Berenson Designers Group Ten Series 6" (152 mm) Center to Center Polished Nickel Pull, - 4141-1014-P
Description
Designers Group Ten Pull 6 Inch For Cabinets
Designers Group Ten pull 6 inch center to center is a Berenson Corporation cabinet handle made from zinc die cast, so it gives a solid metal feel that suits regular cabinet use in kitchens, baths, or shop-built casework. The polished nickel finish provides a bright, reflective surface that visually matches other polished nickel decorative hardware and moldings on the same run. The handle length of 7-3/8 inches spans wider drawer fronts, which helps spread the pulling force over more fastener locations during daily use. A projection of 1-11/16 inches creates hand clearance between the pull and the cabinet face, which matters when gripping the pull on deeper drawer heads. The 11/16 inch width presents a defined edge for fingers to catch, which helps repeat the same grip on doors and drawers across a project.
Key Berenson Pull Details For Job Planning
- The 6 inch center to center dimension sets precise drilling on cabinet fronts, which supports consistent handle spacing across doors and drawers during layout and installation.
- The zinc die cast material gives the pull a rigid structure, which supports stable fastening against wood or composite cabinet faces under frequent opening and closing.
- The polished nickel finish delivers a bright metallic appearance, which helps visually align this pull with other polished nickel elements in a room design.
- The 7-3/8 inch overall length covers a wider area on drawer fronts, which helps distribute hand contact and pulling load across the mounting points.
- The 1-11/16 inch projection defines stand-off from the cabinet surface, which provides finger clearance when installed on both doors and deeper drawer fronts.
Installation Details For 6 Inch Center To Center Pull
The 6 inch center to center measurement on this Berenson Designers Group Ten pull fixes the distance between mounting holes, which simplifies template use when drilling repetitive runs of doors and drawers. The specified 8-32 x 1 inch screw size defines the threaded interface for fastening through standard cabinet door and drawer front thicknesses, which supports a familiar installation process using common cabinet hardware tools. With a 7-3/8 inch overall length, the pull positions its mounting points slightly inboard of the ends, which can help alignment against rail widths on many cabinet styles. The 1-11/16 inch projection sets how far the pull stands off the face, which influences both user grip space and how the hardware clears adjacent faces or trim details.
How This Berenson Pull Works In Real Projects
Where The Designers Group Ten Pull Fits Best
This Berenson Designers Group Ten pull is positioned for use on cabinet doors and drawers where a 6 inch center to center layout is already planned or specified, because that hole spacing is built into the pull design. The zinc die cast construction supports use on residential or shop-built casework where metal pulls are preferred, since the material pairs well with typical wood or composite cabinet fronts. With an overall length of 7-3/8 inches, the pull visually suits medium to larger fronts, so a single handle can span a wider drawer face without looking undersized. The polished nickel finish coordinates with other polished nickel decorative hardware and moldings in the same space, reinforcing a consistent finish selection on hinges, knobs, and other visible fittings.
Details That Support Consistent Cabinet Results
The 6 inch center to center layout on this 4141-1014-P cabinet pull means once hole locations are set for one front, the same spacing repeats across the run, which helps keep reveals and handle lines straight on banks of cabinets. The 1-11/16 inch projection defines how far the gripping surface stands away from the door or drawer, which supports a repeatable hand clearance dimension across the installation. At 11/16 inch width, the pull offers a defined bar profile, which aids consistent finger placement when multiple pulls are used side by side. The polished nickel surface presents the same bright metallic appearance on every unit, which supports uniform reflections along tall cabinet runs or wide drawer stacks. Using a standard 8-32 x 1 inch screw interface also keeps fastening consistent with many other cabinet pulls that share this thread size.
Common Questions About Berenson 4141-1014-P Pull
What is the center to center size on this pull?
The Berenson 4141-1014-P pull has a 6 inch center to center measurement, which sets the distance between mounting holes for drilling cabinet doors and drawers.
How long is the Designers Group Ten cabinet pull overall?
The Designers Group Ten pull has a 7-3/8 inch overall length, which helps it span medium to larger cabinet doors and drawer fronts.
What material is the Berenson 4141-1014-P pull made from?
The Berenson 4141-1014-P pull is made from zinc die cast, which provides a solid metal construction suited to regular cabinet use.
What is the projection of this polished nickel pull?
This polished nickel cabinet pull has a 1-11/16 inch projection, which sets the stand-off from the cabinet face for hand clearance.
How wide is the Berenson Designers Group Ten pull?
The Berenson Designers Group Ten pull is 11/16 inch wide, giving a defined gripping surface across the bar of the handle.
What screw size does this cabinet pull use?
The 4141-1014-P cabinet pull uses 8-32 x 1 inch screws, aligning with common cabinet door and drawer front fastening setups.
Selecting This Pull For Polished Nickel Projects
The Berenson Designers Group Ten Series 6 inch center to center polished nickel pull combines zinc die cast construction, 7-3/8 inch overall length, and 1-11/16 inch projection to support practical cabinet handling on doors and drawers. The polished nickel finish aligns with polished nickel decorative hardware choices throughout a project, while the defined 6 inch center to center spacing supports repeatable hole layouts across multiple fronts. When a project calls for a polished nickel cabinet pull with this specific center to center and size profile, this 4141-1014-P model from Wurth Baer Supply aligns the critical dimensions for straightforward selection.
