Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
inside outside corner molding black 96 describes the HandiSOLUTIONS HandiTRIM Inside/Outside Corner Molding identified as HST4096M, so buyers get a clearly defined trim piece for Handi WALL slatwall installations where panels meet at corners. This molding is part of the trim extrusions offered to finish off the Handi WALL installation, which gives installers a purpose-built way to close out transitions instead of leaving exposed panel edges. The inside/outside corner trim is used to trim slatwall meeting at 90 degree corners, so one profile addresses both inward and outward room corners and simplifies planning around walls and columns. The molding is black, which creates a defined border line against typical slatwall panel surfaces and supports a consistent visual frame around corners. Each molding is 96 feet long according to the SAP description, so it spans long runs of wall without frequent joints and supports continuous corner lines on typical garage or shop walls.
This Inside/Outside Corner Trim is described specifically for slatwall meeting at 90 degree corners, so it is intended to sit where two Handi WALL panel runs intersect and carry the corner from floor toward ceiling in one continuous line. Because the part is a dedicated trim extrusion for finishing off the Handi WALL installation, it is shaped for that system rather than being a generic molding, which helps panels register consistently along the corner. The 96-foot length noted for this black molding means there is ample material to cut segments for multiple wall heights or continuous lengths along various corner conditions on a job. As a HandiTRIM slatwall trim element, it fits within the broader HandiSOLUTIONS slatwall and accessories family, which keeps corner treatment visually aligned with T-Molding seams and other finishing trims around the same installation.
The Inside/Outside Corner Trim HST4096M is defined as trim for slatwall meeting at 90 degree corners, so its primary role is at inside and outside vertical corners where two Handi WALL sections intersect. Being a HandiSOLUTIONS trim extrusion to finish off the Handi WALL installation, it matches the intended geometry of that slatwall system along corner lines rather than acting as a stand-alone decorative molding. The black finish recorded in the SAP description gives the corner molding a consistent visual edge that can tie together adjacent panels and define the boundary between slatwall and adjacent surfaces along the corner. Because this molding is part of the same group of trim extrusions that also covers seams of adjoining slatwall with T-Molding, it allows the corner detail to visually coordinate with other terminations used around the project, from inside corners to panel-to-panel joints.
The product is identified as Inside/Outside Corner Trim, so one profile manages both inside and outside 90 degree corners on Handi WALL layouts, which reduces pattern changes and supports consistent results from one corner condition to the next. As a trim extrusion designed to finish off the Handi WALL installation, it provides a purpose-made termination that aligns with the slatwall product family, which helps maintain even panel spacing and a professional-looking border where walls change direction. The 96-foot length specified for this black molding gives enough run to cut multiple corner pieces from a single part, so long straight corners can be laid out with fewer joints to align or dress. The link to the broader HandiSOLUTIONS slatwall and accessories category positions this molding within a coordinated system of trim, so installers can plan corners, seams, and edges using elements designed to work together on the same Handi WALL installation.
The HandiSOLUTIONS HST4096M Inside/Outside Corner Trim is used to trim Handi WALL slatwall meeting at 90 degree corners, so it finishes vertical inside and outside corners in a coordinated way.
The Inside/Outside Corner Trim is described as a trim extrusion to finish off the Handi WALL installation, so it is shaped for that slatwall system and aligns with its panel layout at corners.
The SAP description lists the molding as 96 feet long, so installers can cut multiple corner pieces from one part and run long vertical or horizontal corners with fewer joints.
This Inside/Outside Corner Trim is used at 90 degree corners where Handi WALL slatwall panels meet, so it sits along the intersection line of two panel runs.
The SAP description records the molding as black, so installed corners present a dark, consistent border that visually frames the Handi WALL panels.
The Inside/Outside Corner Trim is part of the trim extrusions offered to finish off the Handi WALL installation, alongside T-Molding used to cover seams between adjoining slatwall pieces.
The Inside/Outside Corner Molding HST4096M from HandiSOLUTIONS is defined as black trim for slatwall meeting at 90 degree corners, so it directly targets Handi WALL inside and outside corner conditions. As one of the trim extrusions offered to finish off the Handi WALL installation, it works alongside T-Molding that covers seams between adjoining slatwall pieces, which helps keep the entire perimeter and all joints visually consistent. The 96-foot length stated in the SAP description offers extended run capacity, allowing installers to cut multiple pieces from a single molding while maintaining the same profile and color from floor to ceiling across the project.
Sold In: 1 Each