
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
HandiTRIM slatwall trim inside outside corner is a HandiSOLUTIONS molding designed to finish 90 degree angle connections on HandiBR Wall installations, so corners present a clean transition instead of exposed slatwall edges. The trim is described as an inside/outside corner molding, meaning it can be used where two wall runs meet at a right angle, helping one profile handle multiple corner conditions on a project. All moldings are 96 feet long according to the description, giving extended reach along tall garage, closet, or storage walls without frequent splices. The molding is made to frame out the wall and eliminate seams, which supports a more continuous finished appearance across adjoining slatwall panels. This part is described as graphite, giving a dark tone that visually matches graphite HandiBR Wall components for a consistent look across the installation.
The molding is described as 3/4 inch by 3/4 inch, so each leg of the profile covers three quarters of an inch along the adjoining surfaces, giving a defined but compact edge band at the corner. All moldings are 96 feet long per the description, allowing long continuous runs along tall walls or extended horizontal stretches before field-cutting to length for specific conditions. Being identified as trim for HandiBR Wall installations, the extrusion is intended to sit alongside that slatwall system, which guides installers toward matching the profile to that application. The inside/outside corner language signals that the same basic shape serves multiple corner orientations, helping simplify planning when finishing intersecting slatwall runs.
This HandiSOLUTIONS HST13096M molding is described as an inside/outside corner part for HandiBR Wall installations, so it is applied at right angle joints where two slatwall-covered surfaces meet. The trim is made to frame out the wall, meaning it borders the outer edges of the slatwall field rather than sitting randomly within panels, which creates a defined perimeter line around the organized wall area. The description notes that it can be placed on vertical edges, so it works at panel ends that run floor-to-ceiling or alongside door jambs and corners in garage or closet layouts. The same molding may also be used on top and bottom edges, so installers can run it along the upper termination near ceilings and along lower edges near floors for a continuous framed band around the HandiBR Wall field.
The product description stating that parts are made to frame out the wall and eliminate seams means the profile is sized and shaped to sit over panel joints, helping those seams disappear visually once the trim is in place. Because it is intended to make 90 degree angle connections more cosmetically appealing, the molding masks cut panel ends at corners, which reduces the visual impact of minor panel edge variations. The 3/4 inch by 3/4 inch dimension provides enough coverage to conceal typical cut edges and small gaps while keeping the profile relatively compact so it does not dominate the wall. The graphite color description connects the molding to graphite HandiBR Wall components, which supports a more unified appearance when the same tone carries across panels and edges. With each molding described as 96 feet long, installers can run substantial distances with minimal joints, which keeps the framed line straighter and visually cleaner along the full height or width of the wall.
The HandiSOLUTIONS HST13096M molding is used as an inside/outside corner trim on HandiBR Wall installations, so 90 degree joints at wall intersections present a finished, framed appearance.
The inside outside corner design allows one graphite molding profile to address multiple 90 degree conditions, so installers can finish different corner orientations using the same trim part.
The molding can be placed on vertical edges and may also be used on top and bottom edges, so it frames the HandiBR Wall field around all four sides of the installation.
The 3/4 x 3/4 size means each leg of the corner molding extends three quarters of an inch along the adjoining surfaces, covering typical panel edges without creating an oversized border.
The graphite color matches the graphite HandiBR Wall description, so the corner molding blends with the wall panels and supports a consistent finish across the slatwall system.
The 96 foot length lets installers run long vertical or horizontal stretches with fewer joints, so framed edges remain visually continuous along tall or wide HandiBR Wall layouts.
This HandiTRIM slatwall trim extrusion is identified specifically for finishing HandiBR Wall installations in the graphite color, so it aligns with that system when framing corners and edges. The inside/outside corner description means one 3/4 inch by 3/4 inch profile handles multiple 90 degree junctions, simplifying material choices around complex wall layouts. With each molding described as 96 feet long, fewer segments are needed to travel the full height or width of a slatwall field, which supports smoother visual lines along the framed perimeter. For projects calling for a graphite HandiBR Wall field with defined, finished corners and borders, this HandiSOLUTIONS HST13096M molding provides the matching trim profile described for that role.
Sold In: 6 Each