SYS 6 housing 3/4 mtrl black describes a Titus Tool System 6 cam housing designed specifically for 18/19 mm, or 3/4 inch, material. This fastener sits in the RTA and system fittings class, so it is aimed at ready-to-assemble cabinet and furniture constructions where repeatable joints are needed shift after shift. The drop on cam design features a slight lip on the inside that helps secure a top shelf until the screw is set, so the panel holds position while the joint is tightened. This version is identified by manufacturer part number 006395.835.001 and works as a side entry outrigger style fastener, giving additional alignment guidance along the panel edge during assembly. A black finish differentiates this cam visually in production runs and can blend with darker panel interiors when the hardware remains exposed.
This Titus Tool SYS 6 housing works as a side entry outrigger cam, so drilling patterns are set up for access from the panel side rather than the face. The product is suitable for 18/19 mm, or 3/4 inch, panels, so boring depth and location are tuned to that material thickness in cabinet carcasses and shelving. Minimum drilling requirements mean only the core holes for the housing and mating fastener are needed, with no additional edge boring, so multi-spindle or CNC programs stay efficient. Recommended boring bits for outrigger cams are AA201010 at 10 mm and AA203201 at 20 mm right-hand, so shops can match tooling to Titus guidance and maintain clean, repeatable bores in RTA production.
This S6 knock in 18/19 mm side entry outrigger cam in black is built for 3/4 inch panel constructions that rely on RTA fittings. The side entry layout lets the cam engage from the panel edge zone, so cabinet sides, partitions, and top shelves can be drawn together without face access. Because it is intended for 18/19 mm material, the housing sits properly in standard 3/4 inch casework, giving consistent holding across kitchen, bath, or commercial cabinetry using that stock. Drop on cam geometry with a slight internal lip supports the top shelf during assembly, so the shelf rests on the lip while the mating screw is set, which is especially useful when handling larger components on production benches. As part of the fasteners and RTA fittings category, this cam housing integrates into broader knock-down systems used in high volume woodworking.
The Titus linear cam design provides constant tightening loads while driving, so as the cam turns it pulls panels together in a controlled way rather than with a sudden snap. That consistent load helps maintain alignment along the outrigger feature, preventing the joint from shifting as torque is applied. An angle drive feature on the cam is built in for maximum driving comfort, allowing drivers to approach the cam at an angle during assembly; this helps in tight cabinet interiors where straight access is limited. Because the housing can be machine inserted or knocked in with a hammer, the same component serves automated lines and manual workstations, simplifying inventory. No edge boring is required, which means fewer operations per panel, less tool wear on edge heads, and simpler fixtures. Recommended boring bits AA201010 and AA203201 are specified for outrigger cams at 10 mm and 20 mm right-hand respectively, guiding tool selection so hole quality supports consistent knock-in fit and cam performance.
The SYS 6 housing 3/4 mtrl black is designed for 18/19 mm, or 3/4 inch, panels, so it matches common cabinet and furniture stock thickness.
The drop on cam has a slight internal lip that holds the top shelf in place until the screw is set, so the panel stays supported while tightening.
The outrigger style offers easy alignment and added strength, so panels locate consistently and joints resist racking under load.
The cam housing can be machine inserted or knocked in with a hammer, supporting both automated production and manual assembly setups.
The housing needs only minimum drilling and no edge boring, with Titus recommending AA201010 10 mm and AA203201 20 mm right-hand boring bits.
The linear cam design delivers constant tightening loads while driving, so components are pulled together smoothly for predictable joints.
This Titus Tool SYS 6 housing in black ties directly into 18/19 mm, or 3/4 inch, RTA cabinet and furniture programs where speed and consistency matter. Drop on cam geometry with an internal lip, outrigger alignment for added strength, and linear cam tightening loads all support repeatable, production-grade joints. With minimum drilling, no edge boring, and the option to machine insert or knock in with a hammer, this side entry cam housing fits both automated lines and bench assembly workflows for professional woodworking shops.
Sold In: 50 Each