Berenson-R.Christensen Spiral 8-13/16" (224 mm) Center to Center Brushed Nickel Pull, 1143-1BPN-P

Spiral Series Brushed Nickel Pull For Cabinets

Spiral Series brushed nickel pull is a zinc cabinet handle from the R. Christensen by Berenson Spiral collection that adds a consistent decorative look across a run of doors and drawers. The pull uses an 8-13/16 inch (224 mm) center to center dimension, which matches standard drill patterns for modern cabinetry and speeds layout on new installs or changeouts. Its overall 9-3/16 inch length provides a substantial hand grip along wider drawer fronts, which supports smooth opening under load. The brushed nickel finish presents a muted metallic surface that reduces the appearance of fingerprints in routine use. Constructed from zinc, the pull offers a solid feel at the hand while maintaining manageable weight for typical cabinet door configurations. This combination of defined center to center sizing, extended length, and stable material gives installers a predictable hardware choice for both residential and commercial cabinet runs.

Key Spiral Cabinet Pull Details For Projects

• The 8-13/16 inch (224 mm) center to center dimension sets fixed hole spacing, which simplifies jig setup and repeat drilling across multiple cabinet faces during installation work.
• The 9-3/16 inch overall length provides broader hand contact on drawers and doors, which helps users pull heavier cabinet loads with less strain on a single fingertip point.
• The 1 inch projection sets how far the pull stands off the cabinet surface, which provides finger clearance while helping keep the handle within typical kitchen and bath profile lines.
• The 3/4 inch width defines the front face of the pull, which offers a balanced profile that is noticeable on the door without overpowering narrow stile or rail dimensions.
• The brushed nickel finish on zinc creates a consistent metallic appearance, which supports coordination with other brushed nickel hardware in the same room or project line.

Mounting Dimensions That Support Clean Alignment

This R. Christensen by Berenson Spiral Series pull uses an 8-13/16 inch (224 mm) center to center mounting pattern, which gives installers a clear number for drilling or adjusting existing holes. With a 9-3/16 inch overall length, the pull slightly overhangs the mounting points, which frames the screw line and helps hide minor drilling variations at the ends. The 1 inch projection defines the stand-off from the cabinet face, which influences how much space is available for fingers behind the pull during daily use. A 3/4 inch width across the handle creates a visible but controlled front profile, which helps maintain even sight lines along door and drawer rows. Together, these dimensions support consistent alignment and repeatable placement on banks of cabinets.

Using The 1143-1BPN-P Pull In Cabinet Runs

Where This Spiral Series Pull Performs Best

The Berenson-R. Christensen Spiral Series 1143-1BPN-P pull is designed as a decorative handle in the Handles and Pulls category, which makes it suitable for cabinet doors and drawers in woodworking projects. Its 8-13/16 inch (224 mm) center to center sizing aligns with longer fronts such as base cabinet drawers, where wider spread pulls balance the front visually. At 9-3/16 inches overall length, the pull provides extended grip area along broader drawer faces, which is useful on storage pieces that see repeated opening. The 1 inch projection creates defined space behind the pull, which supports comfortable hand access on thicker door edges. Constructed from zinc with a brushed nickel finish, the pull coordinates with other brushed nickel decorative hardware and moldings, which is practical when building a unified look within a kitchen or shop-built casework project.

Why The Dimensions Support Repeatable Installations

The fixed 224 mm center to center measurement lets installers set up drilling templates once and repeat the same spacing across a full room of cabinets, which cuts layout time and helps keep holes consistent. Because the overall length is 9-3/16 inches, the handle extends beyond the screw locations, which visually anchors the pull and can help visually minimize slight alignment differences at the mounting points. The 3/4 inch width offers enough face area to register straight against layout lines during marking, which supports accurate positioning. A 1 inch projection sets a known stand-off from the cabinet surface, which helps designers and installers predict clearances when doors open near walls or adjacent cabinets. With its zinc construction and brushed nickel finish, the pull delivers a stable feel and a uniform surface that maintains the planned appearance across multiple units in the same installation.

Common Questions About This Spiral Cabinet Pull

Selecting This Brushed Nickel Pull For Your Job

The Berenson-R. Christensen Spiral Series 8-13/16 inch (224 mm) center to center brushed nickel pull offers defined dimensions, a 9-3/16 inch overall length, and a 1 inch projection in zinc construction, giving installers a consistent handle choice for coordinating cabinet doors and drawers across a project.