Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
center support for round tubing holds 1-5/16 inch diameter aluminum round tubing so a closet rod stays supported along its span. The Pro Value Series design works as a load-bearing support between end flanges, which helps closet rods stay aligned in everyday use.
This closet rod center support for 1-5/16 inch tubing positions the tubing at a consistent height along the run, which keeps hangers tracking smoothly across the rod. The dull brass finish matches other dull brass closet rod components where a uniform appearance matters.
The Pro Value Series part 54233 47 061 gives installers a specific, repeatable choice when 1-5/16 inch aluminum round tubing is used, which simplifies ordering and replacement on multi-closet projects. The support belongs to the Closet Rods & Flanges product class, so it fits naturally into closet, shelf, and garage organization layouts built around round tubing.
This closet rod center support is specified for 1-5/16 inch diameter aluminum round tubing, so the tubing seats into the support at the correct diameter without extra shimming. The fit concentrates support directly under the rod where hanging load is carried.
The two mounting holes drilled at 1-1/2 inch center-to-center create a predictable anchor footprint on closet side panels or support cleats, which helps installers lay out screw locations in a straight, repeatable line.
The #6 x 3/4 inch screws used with the support tie the bracket into wood substrates within the screw length, which anchors the support while limiting penetration depth into cabinet sides or closet partitions.
This Pro Value Series center support for round tubing fits into closet, shelf, and garage organization projects that use 1-5/16 inch diameter aluminum round tubing as the hanging rod. The support acts as the intermediate bracket between tubing flanges, which helps distribute hanging load along the span.
Because the support is part of the Closet Rods & Flanges product class, it matches typical closet layouts where continuous rods pass through multiple compartments. The dull brass finish lets it sit along a dull brass tube without drawing attention, which keeps the visual focus on a straight rod line.
The 1-1/2 inch center-to-center mounting pattern works on face frames, panels, or cleats with enough width for two #6 x 3/4 inch screws. This pattern helps closet and cabinet builders repeat the same drilling template across multiple compartments, which supports consistent production on shop-built or on-site installations.
On longer closet rods built from 1-5/16 inch aluminum round tubing, placing this center support between end supports helps transfer part of the hanging load into an intermediate panel or support member. That load sharing helps the round tubing maintain its alignment at the middle of the span in normal hanging conditions.
The specific sizing for 1-5/16 inch diameter aluminum round tubing means this dull brass center support locates the rod at a known diameter every time, which allows installers to line up additional supports or flanges using the same rod centerline.
The 1-1/2 inch center-to-center spacing of the two mounting holes sets a fixed measurement that can be transferred to jigs or drilling guides, which supports repeatable screw placement in production cabinet or closet runs.
Using #6 x 3/4 inch screws with the support defines both shank diameter and penetration depth into typical wood materials, which helps control how tightly the bracket pulls to the substrate and how much material is engaged for holding power.
The dull brass finish on the center support visually ties into dull brass closet rod and flange components, which matters when closet interiors are specified around a uniform metal tone. That finish continuity helps align this part with other Pro Value Series dull brass fittings in the same installation.
The manufacturer part number 54233 47 061 uniquely identifies this center support configuration, which simplifies reordering the same dull brass 1-5/16 inch tubing support for future closet expansions or service calls on existing installations.
This center support holds 1-5/16 inch diameter aluminum round tubing, which sets the rod at a defined diameter and helps it track correctly with matching flanges and hangers.
The mounting holes are 1-1/2 inch center-to-center, which gives a consistent drilling pattern so multiple supports line up along a closet side or cleat.
This center support uses #6 x 3/4 inch screws, which sets both the pilot hole size and depth of bite into typical wood closet or cabinet materials.
The support has a dull brass finish, which lets it visually coordinate with dull brass closet rods and flanges across the installation.
This center support is from the Pro Value Series with manufacturer part number 54233 47 061, which clearly ties it to this specific dull brass 1-5/16 inch tubing support.
This center support is used between end flanges on 1-5/16 inch aluminum round tubing runs, which helps carry rod load at mid-span in closet, shelf, or garage organizers.
This Pro Value Series closet rod center support for 1-5/16 inch diameter aluminum round tubing gives a defined way to support rods at mid-span using a dull brass bracket that visually matches dull brass tubing and flanges.
The 1-1/2 inch center-to-center mounting pattern and #6 x 3/4 inch screw specification provide clear installation details. For closet, shelf, or garage organization projects built around 1-5/16 inch round tubing, this center support helps rods stay aligned and supported along the run.
Sold In: 1 Each