Center support for round tubing gives 1-5/16 inch diameter aluminum round tubing a fixed support point along a closet run, which helps the rod carry hanging loads without sagging between end flanges. This Pro Value Series part is a closet rod center support, so it serves as the intermediate bearing point between mounting locations in shelf, closet, and garage organization layouts. The dull nickel finish on the support creates a neutral metallic look that visually matches dull nickel closet hardware, which keeps hardware color consistent across a project. The support is part of the Closet Rods and Flanges product class, so it is sized and shaped to work in the same hardware family as matching tubing and flanges. The manufacturer part number 54233 49 103 identifies this exact dull nickel center support, which helps match replacements or add supports that line up with existing hardware.
The center support for round tubing has two holes for mounting screws, so the load from the closet rod transfers into the mounting surface through two fastener points rather than a single point. The mounting screw holes are set at 1-1/2 inch center to center spacing, which dictates the layout pattern when marking and drilling pilot locations on the supporting surface. The support uses #6 x 3/4 inch screws as the specified fasteners, so the shank and length are matched to the hole size and typical substrate thickness in closet framing and panels. Because the support is intended for 1-5/16 inch diameter aluminum round tubing, the mounting geometry works with that tube size to keep the rod aligned parallel to shelves or closet sides.
This center support for round tubing is specified for 1-5/16 inch diameter aluminum round tubing, so it fits closet rods built around that outside diameter and material. The part sits in the shelf, closet, and garage organization category, which positions it for storage layouts such as hanging closets, wardrobe sections, or garage hanging rails using round tubing. As a component in the Closet Rods and Flanges class, it occupies the intermediate position between end flanges, so it supports spans where the rod would otherwise rely only on its ends. The dull nickel finish matches dull nickel hardware on adjoining closet components, which keeps the overall hardware line visually consistent across multiple supports in the same run.
The two holes for mounting screws on this Pro Value Series center support create a defined pair of fastener locations, so each installation repeats the same screw layout on the substrate. With 1-1/2 inch center to center spacing between those holes, installers can transfer that dimension along long closet runs, which supports straight, repeatable alignment of supports along the tubing. The specified use of #6 x 3/4 inch screws ties the support to a known screw size and length, so drilling and driving operations can be standardized across several supports. Because the support is built for 1-5/16 inch diameter aluminum round tubing, each mounted support positions the rod in the same vertical and horizontal relationship to shelves or side panels, which reduces fitting variation between sections in the same closet or garage system.
The center support for round tubing is designed for 1-5/16 inch diameter aluminum round tubing, so it holds that specific rod size securely along the closet run.
The closet rod center support mounts through two holes for mounting screws, so it fastens to the supporting surface at two points for load transfer.
The support has mounting screw holes set at 1-1/2 inch center to center, which defines the layout dimension for drilling pilot holes on the substrate.
The center support for round tubing has a dull nickel finish, so it presents a muted metallic look that coordinates with dull nickel closet hardware.
The Pro Value Series center support uses #6 x 3/4 inch screws, so the screw diameter and length match the mounting holes and typical closet substrates.
This part is in the Closet Rods and Flanges product class, so it works as the intermediate support component between round closet rod flanges.
This center support for round tubing is built for 1-5/16 inch diameter aluminum round tubing, so it suits closet and garage runs using that specific rod size. The dull nickel finish and Pro Value Series branding align with matching closet rod components, which helps projects carry a consistent hardware line. With two mounting screw holes at 1-1/2 inch center to center and specified #6 x 3/4 inch screws, the support sets out clear fastening points along each run. For storage layouts that rely on 1-5/16 inch tubing and closet rods and flanges components, this center support provides the defined intermediate bearing point the system is designed around.
Sold In: 1 Each