Salice 700 Series Soft-Close Hinge For Cabinets
Salice 700 Series soft-close hinge is a concealed cabinet hinge with a 110 degree opening angle that supports full access to the cabinet interior while keeping hardware hidden for a clean cabinet appearance. The hinge is equipped with Silentia+, an innovative switch to delay the decelerating action, so the closing speed can be tailored to the door behavior for controlled motion. Activation of the Silentia+ switch allows even special doors to obtain the ideal decelerating strength, helping doors close smoothly instead of slamming. The hinge offers integrated soft close motion, so the deceleration is built directly into the hinge body and does not require separate soft-close components in the cabinet. As a concealed cabinet hinge, it belongs to the European standard hinges category, which supports modern frameless and face-frame cabinet construction where a streamlined look and efficient motion are important.
Key Salice Silentia Inset Hinge Advantages
- The 110 degree opening angle allows doors to swing wide enough for comfortable access to shelves and hardware, which can ease installation and everyday cabinet use in kitchen or shop environments.
- The 13.5 mm hinge cup boring depth sets a clear drilling depth target in the door, supporting repeatable cup preparation on drill presses or line-boring machines without guesswork during production.
- The edge bore distance (K) from 3 mm to 6 mm provides flexibility in cup location relative to the door edge, making it easier to align overlays and margins when working with varying cabinet constructions.
- Up to 21 mm overlay capability allows the hinge to work with cabinet designs that require a relatively generous door overlay, helping match existing reveals across a run of cabinets.
- For door thickness up to 25 mm, the hinge supports use on thicker doors often found in higher-end or specialty cabinetry, so door design is not constrained to thin stock.
- Parallel side adjustment supports fine-tuning of side gaps, so doors can be aligned across a bank of cabinets to achieve even reveals and reduce rework after installation.
Mounting Details For Salice C7R6PE9 Installation
The hinge uses a standard 45 mm x 9.5 mm Salice boring pattern, which ties directly into common European line-boring and CNC programs for efficient, repeatable hole layout. The hinge is described as an inset overlay solution for face-frame and frameless applications, so it fits cabinet designs where the door sits within or near the plane of the frame or side panel while still providing an overlay value. The edge bore distance (K) from 3 mm to 6 mm gives a workable window when setting up boring jigs, so installers can adapt to rail widths or panel edges without changing hardware. As a dowel hinge, it is designed to be pressed into properly sized holes in the door, which supports fast, accurate positioning in production settings once the boring pattern is established.
Using This Salice Silentia Hinge In Cabinet Work
Where This Concealed Hinge Performs Best
This Salice 700 Series soft-close hinge fits into the European concealed long arm hinge category, making it suited to both frameless and face-frame cabinet projects that call for hidden hinges and consistent motion. Its role as an inset overlay hinge means it is intended for doors that sit inside the cabinet opening while still covering part of the front, a setup often used in higher-end residential or commercial cabinetry. The ability to handle door thickness up to 25 mm lets it support solid or thick veneered doors without changing the hinge family, which simplifies hardware selection across a project. The 110 degree opening angle gives doors enough swing so interior pullouts or shelves are easier to access during use or service. Because it is compatible with all series 200 mounting plates, it can integrate into existing Salice plate inventories where that interface is already standard on the job.
Why Silentia+ And Adjustments Support Results
The hinge is equipped with Silentia+, an innovative switch to delay the decelerating action, so installers can fine-tune the soft-close response to suit lighter or heavier cabinet doors. Activation of the Silentia+ switch allows even special doors to obtain the ideal decelerating strength, which helps prevent bounce-back or abrupt stops on nonstandard sizes. Integrated soft close motion and enhanced soft close for heavier doors work together to produce a uniform closing action regardless of door size, which is valuable when a bank of doors must close at similar speeds for a consistent look. Parallel side adjustment simplifies the process of dialing in precise door reveals after mounting, reducing the time needed to correct minor misalignments. The hinge meets ANSI/BHMA standards A156.9-2010, indicating it has been tested to a recognized performance standard for cabinet hardware. A lifetime warranty further supports long-term use by backing the hinge over the service life of the cabinet installation.
Common Questions About This Salice Cabinet Hinge
What type of cabinet hinge is the Salice C7R6PE9?
The Salice C7R6PE9 is a concealed cabinet hinge from the 700 Series, designed as a European standard hinge for inset overlay applications on face-frame and frameless cabinets.
How far does this Silentia hinge allow the door to open?
The hinge has a 110 degree opening angle, which lets the door swing wide for easier access to cabinet interiors and hardware during daily use or service.
What door thickness range does this hinge support?
The hinge is specified for door thickness up to 25 mm, so it can be used on thicker doors often found in higher-end or specialty cabinetry without changing hinge families.
How does the Silentia plus soft close adjustment help?
The hinge Silentia+ switch delays the decelerating action, so the closing strength can be adapted and even special doors can achieve an ideal soft-close motion.
What boring details are specified for this Salice hinge?
The hinge uses a 13.5 mm hinge cup boring depth with edge bore distance K from 3 mm to 6 mm and a standard 45 mm x 9.5 mm Salice boring pattern for drilling layouts.
Which mounting plates work with the Salice 700 Series hinge?
The hinge is compatible with all series 200 mounting plates, which allows it to integrate with existing Salice plate systems already used in cabinet installations.
Selecting This Salice Hinge For Your Project
The Salice 700 Series soft-close hinge with Silentia+ brings integrated soft close motion, 110 degree opening, and inset overlay capability into one concealed hinge, aligning well with European frameless and face-frame cabinet construction. Its 13.5 mm cup depth, edge bore distance K from 3 mm to 6 mm, and standard 45 mm x 9.5 mm Salice boring pattern support efficient drilling workflows on shop equipment. Compatibility with all series 200 mounting plates simplifies hardware planning when Salice plates are already standard. For projects needing controlled closing, thicker doors up to 25 mm, and uniform motion across multiple openings, this hinge offers a focused solution ready to be specified, bored, and pressed into production or installation.
